boards: frdm_mcxw71: Add BLE info to doc + Enable second UART instance

- Add second UART needed for bt_tester app. - Update doc with BLE info Signed-off-by: Yassine El Aissaoui <[email protected]>
zephyrproject-rtos · Oct 15, 2024 · d561e98 · d561e98
1 parent 2afe334
commit d561e98
Show file tree

Hide file tree

Showing 3 changed files with 65 additions and 0 deletions.
diff --git a/boards/nxp/frdm_mcxw71/doc/index.rst b/boards/nxp/frdm_mcxw71/doc/index.rst
@@ -63,7 +63,18 @@ The ``frdm_mcxw71`` board target in Zephyr currently supports the following feat
 +-----------+------------+-------------------------------------+
 | LPTMR     | on-chip    | counter                             |
 +-----------+------------+-------------------------------------+
+| BLE       | on-chip    | Bluetooth                           |
++-----------+------------+-------------------------------------+
+
+Fetch Binary Blobs
+******************
+
+To support Bluetooth, frdm_mcxw71 requires fetching binary blobs, which can be
+achieved by running the following command:
+
+.. code-block:: console
 
+   west blobs fetch hal_nxp
 
 Programming and Debugging
 *************************
@@ -140,6 +151,44 @@ should see the following message in the terminal:
    *** Booting Zephyr OS build v3.7.0-xxx-xxxx ***
    Hello World! frdm_mcxw71/mcxw716c
 
+Bluetooth
+=========
+
+BLE functionality requires to fetch binary blobs, so make sure to follow
+the ``Fetch Binary Blobs`` section first.
+
+Two images must be written to the board: one for the host (CM33) and one for the NBU (CM3).
+- To flash the application (CM33) refer to the ``Flashing`` section above.
+- To flash the NBU, follow the instructions below:
+
+   * Install ``blhost`` from NXP's website. This is the tool that will allow you to flash the NBU.
+   * Enter ISP mode. To boot the MCU in ISP mode, follow these steps:
+      - Disconnect the ``FRDM-MCXW71`` board from all power sources.
+      - Keep the ``SW3`` (ISP) button on the board pressed, while connecting the board to the host computer USB port.
+      - Release the ``SW3`` (ISP) button. The MCXW71 MCU boots in ISP mode.
+      - Reconnect any external power supply, if needed.
+   * Use the following command to flash NBU file:
+
+.. code-block:: console
+
+   # On Windows
+   blhost.exe -p COMxx -- receive-sb-file mcxw71_nbu_ble.sb3
+
+   # On Linux
+   ./blhost -p /dev/ttyxx -- receive-sb-file mcxw71_nbu_ble.sb3
+
+Please consider changing ``COMxx`` on Windows or ``ttyxx`` on Linux to the serial port used by your board.
+
+The NBU file can be found in : ``<zephyr workspace>/modules/hal/nxp/zephyr/blobs/mcxw71/mcxw71_nbu_ble.sb3``
+
+For more details:
+
+.. _MCXW71 In-System Programming Utility:
+   https://docs.nxp.com/bundle/AN14427/page/topics/introduction.html
+
+.. _blhost Website:
+   https://www.nxp.com/search?keyword=blhost&start=0
+
 References
 **********
 

diff --git a/boards/nxp/frdm_mcxw71/frdm_mcxw71-pinctrl.dtsi b/boards/nxp/frdm_mcxw71/frdm_mcxw71-pinctrl.dtsi
@@ -6,6 +6,14 @@
 #include <nxp/mcx/MCXW716CMFTA-pinctrl.h>
 
 &pinctrl {
+	pinmux_lpuart0: pinmux_lpuart0 {
+		group0 {
+			pinmux = <LPUART0_RX_PTA16>, <LPUART0_TX_PTA17>;
+			drive-strength = "low";
+			slew-rate = "fast";
+		};
+	};
+
 	pinmux_lpuart1: pinmux_lpuart1 {
 		group0 {
 			pinmux = <LPUART1_RX_PTC2>, <LPUART1_TX_PTC3>;

diff --git a/boards/nxp/frdm_mcxw71/frdm_mcxw71.dts b/boards/nxp/frdm_mcxw71/frdm_mcxw71.dts
@@ -25,6 +25,7 @@
 		zephyr,sram = &stcm0;
 		zephyr,console = &lpuart1;
 		zephyr,shell-uart = &lpuart1;
+		zephyr,uart-pipe = &lpuart0;
 	};
 
 	user_led {
@@ -52,6 +53,13 @@
 	status = "okay";
 };
 
+&lpuart0 {
+	current-speed = <115200>;
+	status =  "okay";
+	pinctrl-0 = <&pinmux_lpuart0>;
+	pinctrl-names = "default";
+};
+
 &lpuart1 {
 	current-speed = <115200>;
 	status =  "okay";