boards: st: introduce new STM32F413H-DISCO discovery kit

Add the stm32f413h_disco target to the boards/st
Add the PLLi2S when needed by the USB or SDMMC or RNG.

Signed-off-by: Francois Ramu <[email protected]>

boards/st/stm32f412g_disco/doc/index.rst

@@ -41,7 +41,7 @@ More information about the board can be found at the `32F412GDISCOVERY website`_
 Hardware
 ********
 
-STM32F469I-DISCO Discovery kit provides the following hardware components:
+STM32F412G-DISCO Discovery kit provides the following hardware components:
 
 - STM32F412ZGT6 in LQFP144 package
 - ARM |reg| 32-bit Cortex |reg| -M4 CPU with FPU

boards/st/stm32f413h_disco/Kconfig.stm32f413h_disco

@@ -0,0 +1,5 @@
+# Copyright (c) 2024 STMicroelectronics
+# SPDX-License-Identifier: Apache-2.0
+
+config BOARD_STM32F413H_DISCO
+	select SOC_STM32F413XX

boards/st/stm32f413h_disco/arduino_r3_connector.dtsi

@@ -0,0 +1,40 @@
+/*
+ * Copyright (c) 2024 STMicroelectronics
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ */
+
+/ {
+	arduino_header: connector {
+		compatible = "arduino-header-r3";
+		#gpio-cells = <2>;
+		gpio-map-mask = <0xffffffff 0xffffffc0>;
+		gpio-map-pass-thru = <0 0x3f>;
+		gpio-map = <0 0 &gpioc 0 0>,	/* A0 */
+			   <1 0 &gpioa 1 0>,	/* A1 */
+			   <2 0 &gpioa 2 0>,	/* A2 */
+			   <3 0 &gpioa 5 0>,	/* A3 */
+			   <4 0 &gpiob 1 0>,	/* A4 */
+			   <5 0 &gpioc 4 0>,	/* A5 */
+			   <6 0 &gpiof 6 0>,	/* D0 */
+			   <7 0 &gpiof 7 0>,	/* D1 */
+			   <8 0 &gpiog 13 0>,	/* D2 */
+			   <9 0 &gpiof 10 0>,	/* D3 */
+			   <10 0 &gpiob 6 0>,	/* D4 */
+			   <11 0 &gpioe 6 0>,	/* D5 */
+			   <12 0 &gpiob 0 0>,	/* D6 */
+			   <13 0 &gpioc 13 0>,	/* D7 */
+			   <14 0 &gpioa 4 0>,	/* D8 */
+			   <15 0 &gpiob 8 0>,	/* D9 */
+			   <16 0 &gpioa 15 0>,	/* D10 */
+			   <17 0 &gpiob 5 0>,	/* D11 */
+			   <18 0 &gpiob 4 0>,	/* D12 */
+			   <19 0 &gpiob 12 0>,	/* D13 */
+			   <20 0 &gpiob 11 0>,	/* D14 */
+			   <21 0 &gpiob 10 0>;	/* D15 */
+	};
+};
+
+arduino_i2c: &i2c2 {};
+arduino_spi: &spi3 {};
+arduino_serial: &uart7 {};

boards/st/stm32f413h_disco/board.cmake

@@ -0,0 +1,10 @@
+# SPDX-License-Identifier: Apache-2.0
+
+# keep first
+board_runner_args(stm32cubeprogrammer "--port=swd" "--reset-mode=hw")
+board_runner_args(jlink "--device=STM32F413ZH" "--speed=4000")
+
+# keep first
+include(${ZEPHYR_BASE}/boards/common/stm32cubeprogrammer.board.cmake)
+include(${ZEPHYR_BASE}/boards/common/openocd.board.cmake)
+include(${ZEPHYR_BASE}/boards/common/jlink.board.cmake)

boards/st/stm32f413h_disco/board.yml

@@ -0,0 +1,6 @@
+board:
+  name: stm32f413h_disco
+  full_name: STM32F413H Discovery
+  vendor: st
+  socs:
+    - name: stm32f413xx

boards/st/stm32f413h_disco/doc/index.rst

@@ -0,0 +1,206 @@
+.. zephyr:board:: stm32f413h_disco
+
+Overview
+********
+
+The STM32F413H-DISCO Discovery kit features an ARM Cortex-M4 based STM32F413ZH MCU
+with a wide range of connectivity support and configurations Here are
+some highlights of the STM32F413H-DISCO board:
+
+
+- STM32F413ZHT6 microcontroller featuring 1.5 Mbyte of Flash memory and 320 Kbytes of RAM in an LQFP144 package
+- On-board ST-LINK/V2-1 SWD debugger supporting USB re-enumeration capability:
+
+       - USB virtual COM port
+       - mass storage
+       - debug port
+
+- 1.54 inch 240x240 pixel TFT color LCD with parallel interface and capacitive touchscreen
+- I2S Audio CODEC, with a stereo headset jack, including analog microphone input and a loudspeaker output
+- Stereo digital MEMS microphones
+- MicroSD card connector extension
+- I2C extension connector
+- 128 Mbit Quad-SPI Nor Flash
+- 8 Mbit 16-bit wide PSRAM
+- Reset and User buttons
+- Two color user LEDs.
+- USB OTG FS with Micro-AB connector
+- Four power supply options:
+
+       - ST-LINK/V2-1 USB connector
+       - User USB FS connector
+       - VIN from Arduino* connectors
+       - + 5 V from Arduino* connectors
+
+- Two power supplies for MCU: 2.0 V and 3.3 V
+- Compatible with Arduino(tm) Uno revision 3 connectors
+- Extension connector for direct access to various features of STM32F413ZHT6 MCU
+- Comprehensive free software including a variety of examples, part of STM32Cube package
+
+More information about the board can be found at the `32F413HDISCOVERY website`_.
+
+Hardware
+********
+
+STM32F413H-DISCO Discovery kit provides the following hardware components:
+
+- STM32F413ZHT6 in LQFP144 package
+- ARM |reg| 32-bit Cortex |reg| -M4 CPU with FPU
+- 100 MHz max CPU frequency
+- VDD from 1.7 V to 3.6 V
+- 1.5 MB Flash
+- 320 KB SRAM
+- GPIO with external interrupt capability
+- LCD parallel interface, 8080/6800 modes
+- 1x12-bit ADC with 16 channels
+- RTC
+- Advanced-control Timer
+- General Purpose Timers (12)
+- Watchdog Timers (2)
+- USART/UART (10)
+- I2C (4)
+- SPI (5)
+- SDIO
+- SAI
+- 3xCAN
+- USB OTG 2.0 Full-speed
+- CRC calculation unit
+- True random number generator
+- DMA Controller
+
+More information about STM32F413ZH can be found here:
+       - `STM32F413ZH on www.st.com`_
+       - `STM32F413 reference manual`_
+
+Supported Features
+==================
+
+The Zephyr STM32F413H-DISCO board configuration supports the following hardware features:
+
++-----------+------------+-------------------------------------+
+| Interface | Controller | Driver/Component                    |
++===========+============+=====================================+
+| NVIC      | on-chip    | nested vector interrupt controller  |
++-----------+------------+-------------------------------------+
+| UART      | on-chip    | serial port-polling;                |
+|           |            | serial port-interrupt               |
++-----------+------------+-------------------------------------+
+| PINMUX    | on-chip    | pinmux                              |
++-----------+------------+-------------------------------------+
+| GPIO      | on-chip    | gpio                                |
++-----------+------------+-------------------------------------+
+| I2C       | on-chip    | i2c                                 |
++-----------+------------+-------------------------------------+
+| SPI       | on-chip    | spi                                 |
++-----------+------------+-------------------------------------+
+
+Other hardware features are not yet supported on Zephyr porting.
+
+The default configuration can be found in
+:zephyr_file:`boards/st/stm32f413h_disco/stm32f413h_disco_defconfig`
+
+
+Pin Mapping
+===========
+
+STM32F413H-DISCO Discovery kit has 8 GPIO controllers. These controllers are responsible for pin muxing,
+input/output, pull-up, etc.
+
+For more details please refer to `32F413HDISCOVERY board User Manual`_.
+
+Default Zephyr Peripheral Mapping:
+----------------------------------
+- UART_6_TX : PG14
+- UART_6_RX : PG9
+- LD1 : PE3
+- LD2 : PC5
+
+System Clock
+============
+
+STM32F413H-DISCO System Clock could be driven by internal or external oscillator,
+as well as main PLL clock. By default System clock is driven by PLL clock at 100MHz,
+driven internal oscillator.
+
+Serial Port
+===========
+
+The STM32F413H-DISCO Discovery kit has up to 10 UARTs. The Zephyr console output is assigned to UART6.
+Default settings are 115200 8N1.
+
+
+Programming and Debugging
+*************************
+
+STM32F413H-DISCO Discovery kit includes an ST-LINK/V2 embedded debug tool interface.
+
+Applications for the STM32F413H-DISCO board configuration can be built and
+flashed in the usual way (see :ref:`build_an_application` and
+:ref:`application_run` for more details).
+
+Flashing
+========
+
+The board is configured to be flashed using west `STM32CubeProgrammer`_ runner,
+so its :ref:`installation <stm32cubeprog-flash-host-tools>` is required.
+
+Alternatively, OpenOCD or JLink can also be used to flash the board using
+the ``--runner`` (or ``-r``) option:
+
+.. code-block:: console
+
+   $ west flash --runner openocd
+   $ west flash --runner jlink
+
+Flashing an application to STM32F413H-DISCO
+-------------------------------------------
+
+Connect the STM32F413H-DISCO Discovery kit to your host computer using
+the USB port, then run a serial host program to connect with your
+board:
+
+.. code-block:: console
+
+   $ minicom -D /dev/ttyACM0
+
+Then build and flash an application. Here is an example for the
+:zephyr:code-sample:`hello_world` application.
+
+.. zephyr-app-commands::
+   :zephyr-app: samples/hello_world
+   :board: stm32f413h_disco
+   :goals: build flash
+
+You should see the following message on the console:
+
+.. code-block:: console
+
+   Hello World! stm32f413h_disco/stm32f413xx
+
+
+Debugging
+=========
+
+You can debug an application in the usual way.  Here is an example for the
+:zephyr:code-sample:`hello_world` application.
+
+.. zephyr-app-commands::
+   :zephyr-app: samples/hello_world
+   :board: stm32f413h_disco
+   :maybe-skip-config:
+   :goals: debug
+
+.. _32F413HDISCOVERY website:
+   https://www.st.com/en/evaluation-tools/32f413hdiscovery.html
+
+.. _32F413HDISCOVERY board User Manual:
+   https://www.st.com/resource/en/user_manual/um2135-discovery-kit-with-stm32f413zh-mcu-stmicroelectronics.pdf
+
+.. _STM32F413ZH on www.st.com:
+   https://www.st.com/en/microcontrollers/stm32f413zh.html
+
+.. _STM32F413 reference manual:
+   https://www.st.com/resource/en/reference_manual/rm0430-stm32f413423-advanced-armbased-32bit-mcus-stmicroelectronics.pdf
+
+.. _STM32CubeProgrammer:
+   https://www.st.com/en/development-tools/stm32cubeprog.html

boards/st/stm32f413h_disco/stm32f413h_disco.dts

@@ -0,0 +1,102 @@
+/*
+ * Copyright (c) 2024 STMicroelectronics
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ */
+
+/dts-v1/;
+#include <st/f4/stm32f413Xh.dtsi>
+#include <st/f4/stm32f413z(g-h)tx-pinctrl.dtsi>
+#include "arduino_r3_connector.dtsi"
+#include <zephyr/dt-bindings/input/input-event-codes.h>
+
+/ {
+	model = "STMicroelectronics STM32F413H-DISCO board";
+	compatible = "st,stm32f413h-disco";
+
+	chosen {
+		zephyr,console = &usart6;
+		zephyr,shell-uart = &usart6;
+		zephyr,sram = &sram0;
+		zephyr,flash = &flash0;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		green_led_1: led_1 {
+			gpios = <&gpioc 5 GPIO_ACTIVE_HIGH>;
+			label = "User LD1";
+		};
+		red_led_2: led_2 {
+			gpios = <&gpioe 3 GPIO_ACTIVE_HIGH>;
+			label = "User LD4";
+		};
+	};
+
+	aliases {
+		led0 = &green_led_1;
+		led1 = &red_led_2;
+
+	};
+};
+
+&clk_lsi {
+	status = "okay";
+};
+
+&clk_hse {
+	hse-bypass;
+	clock-frequency = <DT_FREQ_M(8)>; /* STLink 8MHz clock */
+	status = "okay";
+};
+
+&pll {
+	div-m = <4>;
+	mul-n = <100>;
+	div-p = <2>;
+	div-q = <8>;
+	clocks = <&clk_hse>;
+	status = "okay";
+};
+
+&rcc {
+	clocks = <&pll>;
+	clock-frequency = <DT_FREQ_M(100)>;
+	ahb-prescaler = <1>;
+	apb1-prescaler = <2>;
+	apb2-prescaler = <1>;
+};
+
+&usart6 {
+	pinctrl-0 = <&usart6_tx_pg14 &usart6_rx_pg9>;
+	pinctrl-names = "default";
+	current-speed = <115200>;
+	status = "okay";
+};
+
+&uart7 {
+	pinctrl-0 = <&uart7_tx_pf7 &uart7_rx_pf6>;
+	pinctrl-names = "default";
+	current-speed = <115200>;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-0 = <&i2c2_scl_pb10 &i2c2_sda_pb11>;
+	pinctrl-names = "default";
+	clock-frequency = <I2C_BITRATE_FAST>;
+	status = "okay";
+};
+
+&spi3 {
+	pinctrl-0 = <&spi3_nss_pa15 &spi3_sck_pb12
+		     &spi3_miso_pb4 &spi3_mosi_pb5>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&rtc {
+	clocks = <&rcc STM32_CLOCK_BUS_APB1 0x10000000>,
+		 <&rcc STM32_SRC_LSI RTC_SEL(2)>;
+	status = "okay";
+};

boards/st/stm32f413h_disco/stm32f413h_disco.yaml

@@ -0,0 +1,14 @@
+identifier: stm32f413h_disco
+name: ST STM32F413H Discovery
+type: mcu
+arch: arm
+toolchain:
+  - zephyr
+  - gnuarmemb
+  - xtools
+supported:
+  - arduino_gpio
+  - arduino_serial
+  - arduino_i2c
+  - arduino_spi
+vendor: st