Update documented max PIN values, to accomodate RP2350B (#2072)

src/common/pico_stdlib_headers/include/pico/stdlib.h

@@ -57,15 +57,15 @@ extern "C" {
 #include "pico/stdio_semihosting.h"
 #endif
 
-// PICO_CONFIG: PICO_DEFAULT_LED_PIN, Optionally define a pin that drives a regular LED on the board, default=Usually provided via board header, group=pico_stdlib
+// PICO_CONFIG: PICO_DEFAULT_LED_PIN, Optionally define a pin that drives a regular LED on the board, default=Usually provided via board header, type=int, min=0, max=47 on RP2350B, 29 otherwise, group=pico_stdlib
 
 // PICO_CONFIG: PICO_DEFAULT_LED_PIN_INVERTED, 1 if LED is inverted or 0 if not, type=int, default=0, group=pico_stdlib
 #ifndef PICO_DEFAULT_LED_PIN_INVERTED
 #define PICO_DEFAULT_LED_PIN_INVERTED 0
 #endif
 
-// PICO_CONFIG: PICO_DEFAULT_WS2812_PIN, Optionally define a pin that controls data to a WS2812 compatible LED on the board, group=pico_stdlib
-// PICO_CONFIG: PICO_DEFAULT_WS2812_POWER_PIN, Optionally define a pin that controls power to a WS2812 compatible LED on the board, group=pico_stdlib
+// PICO_CONFIG: PICO_DEFAULT_WS2812_PIN, Optionally define a pin that controls data to a WS2812 compatible LED on the board, type=int, min=0, max=47 on RP2350B, 29 otherwise, group=pico_stdlib
+// PICO_CONFIG: PICO_DEFAULT_WS2812_POWER_PIN, Optionally define a pin that controls power to a WS2812 compatible LED on the board, type=int, min=0, max=47 on RP2350B, 29 otherwise, group=pico_stdlib
 
 /*! \brief Set up the default UART and assign it to the default GPIOs
  *  \ingroup pico_stdlib

src/rp2_common/hardware_gpio/include/hardware/gpio.h

@@ -1403,12 +1403,12 @@ extern void gpio_debug_pins_init(void);
 #endif
 
 
-// PICO_CONFIG: PICO_DEBUG_PIN_BASE, First pin to use for debug output (if enabled), min=0, max=28, default=19, group=hardware_gpio
+// PICO_CONFIG: PICO_DEBUG_PIN_BASE, First pin to use for debug output (if enabled), min=0, max=31 on RP2350B, 29 otherwise, default=19, group=hardware_gpio
 #ifndef PICO_DEBUG_PIN_BASE
 #define PICO_DEBUG_PIN_BASE 19u
 #endif
 
-// PICO_CONFIG: PICO_DEBUG_PIN_COUNT, Number of pins to use for debug output (if enabled), min=1, max=28, default=3, group=hardware_gpio
+// PICO_CONFIG: PICO_DEBUG_PIN_COUNT, Number of pins to use for debug output (if enabled), min=1, max=32 on RP2350B, 30 otherwise, default=3, group=hardware_gpio
 #ifndef PICO_DEBUG_PIN_COUNT
 #define PICO_DEBUG_PIN_COUNT 3u
 #endif

src/rp2_common/hardware_i2c/include/hardware/i2c.h

@@ -55,8 +55,8 @@ extern "C" {
 typedef struct i2c_inst i2c_inst_t;
 
 // PICO_CONFIG: PICO_DEFAULT_I2C, Define the default I2C for a board, min=0, max=1, default=Usually provided via board header, group=hardware_i2c
-// PICO_CONFIG: PICO_DEFAULT_I2C_SDA_PIN, Define the default I2C SDA pin, min=0, max=29, default=Usually provided via board header, group=hardware_i2c
-// PICO_CONFIG: PICO_DEFAULT_I2C_SCL_PIN, Define the default I2C SCL pin, min=0, max=29, default=Usually provided via board header, group=hardware_i2c
+// PICO_CONFIG: PICO_DEFAULT_I2C_SDA_PIN, Define the default I2C SDA pin, min=0, max=47 on RP2350B, 29 otherwise, default=Usually provided via board header, group=hardware_i2c
+// PICO_CONFIG: PICO_DEFAULT_I2C_SCL_PIN, Define the default I2C SCL pin, min=0, max=47 on RP2350B, 29 otherwise, default=Usually provided via board header, group=hardware_i2c
 
 /** The I2C identifiers for use in I2C functions.
  *

src/rp2_common/hardware_spi/include/hardware/spi.h

@@ -40,10 +40,10 @@ extern "C" {
  */
 
 // PICO_CONFIG: PICO_DEFAULT_SPI, Define the default SPI for a board, min=0, max=1, default=Usually provided via board header, group=hardware_spi
-// PICO_CONFIG: PICO_DEFAULT_SPI_SCK_PIN, Define the default SPI SCK pin, min=0, max=29, default=Usually provided via board header, group=hardware_spi
-// PICO_CONFIG: PICO_DEFAULT_SPI_TX_PIN, Define the default SPI TX pin, min=0, max=29, default=Usually provided via board header, group=hardware_spi
-// PICO_CONFIG: PICO_DEFAULT_SPI_RX_PIN, Define the default SPI RX pin, min=0, max=29, default=Usually provided via board header, group=hardware_spi
-// PICO_CONFIG: PICO_DEFAULT_SPI_CSN_PIN, Define the default SPI CSN pin, min=0, max=29, default=Usually provided via board header, group=hardware_spi
+// PICO_CONFIG: PICO_DEFAULT_SPI_SCK_PIN, Define the default SPI SCK pin, min=0, max=47 on RP2350B, 29 otherwise, default=Usually provided via board header, group=hardware_spi
+// PICO_CONFIG: PICO_DEFAULT_SPI_TX_PIN, Define the default SPI TX pin, min=0, max=47 on RP2350B, 29 otherwise, default=Usually provided via board header, group=hardware_spi
+// PICO_CONFIG: PICO_DEFAULT_SPI_RX_PIN, Define the default SPI RX pin, min=0, max=47 on RP2350B, 29 otherwise, default=Usually provided via board header, group=hardware_spi
+// PICO_CONFIG: PICO_DEFAULT_SPI_CSN_PIN, Define the default SPI CSN pin, min=0, max=47 on RP2350B, 29 otherwise, default=Usually provided via board header, group=hardware_spi
 
 /**
  * \brief Opaque type representing an SPI instance.

src/rp2_common/hardware_uart/include/hardware/uart.h

@@ -34,8 +34,8 @@ extern "C" {
 #endif
 
 // PICO_CONFIG: PICO_DEFAULT_UART, Define the default UART used for printf etc, min=0, max=1, default=Usually provided via board header, group=hardware_uart
-// PICO_CONFIG: PICO_DEFAULT_UART_TX_PIN, Define the default UART TX pin, min=0, max=29, default=Usually provided via board header, group=hardware_uart
-// PICO_CONFIG: PICO_DEFAULT_UART_RX_PIN, Define the default UART RX pin, min=0, max=29, default=Usually provided via board header, group=hardware_uart
+// PICO_CONFIG: PICO_DEFAULT_UART_TX_PIN, Define the default UART TX pin, min=0, max=47 on RP2350B, 29 otherwise, default=Usually provided via board header, group=hardware_uart
+// PICO_CONFIG: PICO_DEFAULT_UART_RX_PIN, Define the default UART RX pin, min=0, max=47 on RP2350B, 29 otherwise, default=Usually provided via board header, group=hardware_uart
 
 // PICO_CONFIG: PICO_DEFAULT_UART_BAUD_RATE, Define the default UART baudrate, max=921600, default=115200, group=hardware_uart
 #ifndef PICO_DEFAULT_UART_BAUD_RATE

src/rp2_common/pico_bootsel_via_double_reset/pico_bootsel_via_double_reset.c

@@ -18,7 +18,7 @@
 #define PICO_BOOTSEL_VIA_DOUBLE_RESET_TIMEOUT_MS 200
 #endif
 
-// PICO_CONFIG: PICO_BOOTSEL_VIA_DOUBLE_RESET_ACTIVITY_LED, Optionally define a pin to use as bootloader activity LED when BOOTSEL mode is entered via reset double tap, type=int, min=0, max=29, group=pico_bootsel_via_double_reset
+// PICO_CONFIG: PICO_BOOTSEL_VIA_DOUBLE_RESET_ACTIVITY_LED, Optionally define a pin to use as bootloader activity LED when BOOTSEL mode is entered via reset double tap, type=int, min=0, max=47 on RP2350B, 29 otherwise, group=pico_bootsel_via_double_reset
 
 // PICO_CONFIG: PICO_BOOTSEL_VIA_DOUBLE_RESET_INTERFACE_DISABLE_MASK, Optionally disable either the mass storage interface (bit 0) or the PICOBOOT interface (bit 1) when entering BOOTSEL mode via double reset, type=int, min=0, max=3, default=0, group=pico_bootsel_via_double_reset
 #ifndef PICO_BOOTSEL_VIA_DOUBLE_RESET_INTERFACE_DISABLE_MASK

src/rp2_common/pico_cyw43_driver/include/pico/cyw43_driver.h

@@ -69,17 +69,17 @@ void cyw43_driver_deinit(struct async_context *context);
 
 // PICO_CONFIG: CYW43_PIN_WL_DYNAMIC, flag to indicate if cyw43 SPI pins can be changed at runtime, type=bool, advanced=true, group=pico_cyw43_driver
 
-// PICO_CONFIG: CYW43_DEFAULT_PIN_WL_REG_ON, gpio pin to power up the cyw43 chip, type=int, advanced=true, group=pico_cyw43_driver
+// PICO_CONFIG: CYW43_DEFAULT_PIN_WL_REG_ON, gpio pin to power up the cyw43 chip, type=int, min=0, max=47 on RP2350B, 29 otherwise, advanced=true, group=pico_cyw43_driver
 
-// PICO_CONFIG: CYW43_DEFAULT_PIN_WL_DATA_OUT, gpio pin for spi data out to the cyw43 chip, type=int, advanced=true, group=pico_cyw43_driver
+// PICO_CONFIG: CYW43_DEFAULT_PIN_WL_DATA_OUT, gpio pin for spi data out to the cyw43 chip, type=int, min=0, max=47 on RP2350B, 29 otherwise, advanced=true, group=pico_cyw43_driver
 
-// PICO_CONFIG: CYW43_DEFAULT_PIN_WL_DATA_IN, gpio pin for spi data in from the cyw43 chip, type=int, advanced=true, group=pico_cyw43_driver
+// PICO_CONFIG: CYW43_DEFAULT_PIN_WL_DATA_IN, gpio pin for spi data in from the cyw43 chip, type=int, min=0, max=47 on RP2350B, 29 otherwise, advanced=true, group=pico_cyw43_driver
 
-// PICO_CONFIG: CYW43_DEFAULT_PIN_WL_HOST_WAKE, gpio (irq) pin for the irq line from the cyw43 chip, type=int, advanced=true, group=pico_cyw43_driver
+// PICO_CONFIG: CYW43_DEFAULT_PIN_WL_HOST_WAKE, gpio (irq) pin for the irq line from the cyw43 chip, type=int, min=0, max=47 on RP2350B, 29 otherwise, advanced=true, group=pico_cyw43_driver
 
-// PICO_CONFIG: CYW43_DEFAULT_PIN_WL_CLOCK, gpio pin for the spi clock line to the cyw43 chip, type=int, advanced=true, group=pico_cyw43_driver
+// PICO_CONFIG: CYW43_DEFAULT_PIN_WL_CLOCK, gpio pin for the spi clock line to the cyw43 chip, type=int, min=0, max=47 on RP2350B, 29 otherwise, advanced=true, group=pico_cyw43_driver
 
-// PICO_CONFIG: CYW43_DEFAULT_PIN_WL_CS, gpio pin for the spi chip select to the cyw43 chip, type=int, advanced=true, group=pico_cyw43_driver
+// PICO_CONFIG: CYW43_DEFAULT_PIN_WL_CS, gpio pin for the spi chip select to the cyw43 chip, type=int, min=0, max=47 on RP2350B, 29 otherwise, advanced=true, group=pico_cyw43_driver
 
 #if CYW43_PIO_CLOCK_DIV_DYNAMIC
 /*! \brief Set the clock divisor for the cyw43 pio clock

src/rp2_common/pico_stdio_usb/include/pico/stdio_usb.h

@@ -71,7 +71,7 @@
 #define PICO_STDIO_USB_DEINIT_DELAY_MS 110
 #endif
 
-// PICO_CONFIG: PICO_STDIO_USB_RESET_BOOTSEL_ACTIVITY_LED, Optionally define a pin to use as bootloader activity LED when BOOTSEL mode is entered via USB (either VIA_BAUD_RATE or VIA_VENDOR_INTERFACE), type=int, min=0, max=29, group=pico_stdio_usb
+// PICO_CONFIG: PICO_STDIO_USB_RESET_BOOTSEL_ACTIVITY_LED, Optionally define a pin to use as bootloader activity LED when BOOTSEL mode is entered via USB (either VIA_BAUD_RATE or VIA_VENDOR_INTERFACE), type=int, min=0, max=47 on RP2350B, 29 otherwise, group=pico_stdio_usb
 
 // PICO_CONFIG: PICO_STDIO_USB_RESET_BOOTSEL_FIXED_ACTIVITY_LED, Whether the pin specified by PICO_STDIO_USB_RESET_BOOTSEL_ACTIVITY_LED is fixed or can be modified by picotool over the VENDOR USB interface, type=bool, default=0, group=pico_stdio_usb
 #ifndef PICO_STDIO_USB_RESET_BOOTSEL_FIXED_ACTIVITY_LED

tools/extract_configs.py

@@ -63,19 +63,25 @@ def ValidateAttrs(config_name, config_attrs, file_path, linenum):
         assert 'enumvalues' not in config_attrs
         _min = _max = _default = None
         if config_attrs.get('min', None) is not None:
-            value = config_attrs['min']
-            m = re.match(r'^(\d+)e(\d+)$', value.lower())
-            if m:
-                _min = int(m.group(1)) * 10**int(m.group(2))
-            else:
-                _min = int(value, 0)
+            try:
+                value = config_attrs['min']
+                m = re.match(r'^(\d+)e(\d+)$', value.lower())
+                if m:
+                    _min = int(m.group(1)) * 10**int(m.group(2))
+                else:
+                    _min = int(value, 0)
+            except ValueError:
+                logger.info('{} at {}:{} has non-integer min value "{}"'.format(config_name, file_path, linenum, config_attrs['min']))
         if config_attrs.get('max', None) is not None:
-            value = config_attrs['max']
-            m = re.match(r'^(\d+)e(\d+)$', value.lower())
-            if m:
-                _max = int(m.group(1)) * 10**int(m.group(2))
-            else:
-                _max = int(value, 0)
+            try:
+                value = config_attrs['max']
+                m = re.match(r'^(\d+)e(\d+)$', value.lower())
+                if m:
+                    _max = int(m.group(1)) * 10**int(m.group(2))
+                else:
+                    _max = int(value, 0)
+            except ValueError:
+                logger.info('{} at {}:{} has non-integer max value "{}"'.format(config_name, file_path, linenum, config_attrs['max']))
         if config_attrs.get('default', None) is not None:
             if '/' not in config_attrs['default']:
                 try:
@@ -86,7 +92,7 @@ def ValidateAttrs(config_name, config_attrs, file_path, linenum):
                     else:
                         _default = int(value, 0)
                 except ValueError:
-                    pass
+                    logger.info('{} at {}:{} has non-integer default value "{}"'.format(config_name, file_path, linenum, config_attrs['default']))
         if _min is not None and _max is not None:
             if _min > _max:
                 raise Exception('{} at {}:{} has min {} > max {}'.format(config_name, file_path, linenum, config_attrs['min'], config_attrs['max']))