nip45: add hyperloglog relay response

45.md

@@ -29,29 +29,65 @@ In case a relay uses probabilistic counts, it MAY indicate it in the response wi
 
 Whenever the relay decides to refuse to fulfill the `COUNT` request, it MUST return a `CLOSED` message.
 
-## Examples
+## HyperLogLog
 
-### Followers count
+Relays may return an HyperLogLog value together with the count, hex-encoded.
 
 ```
-["COUNT", <subscription_id>, {"kinds": [3], "#p": [<pubkey>]}]
-["COUNT", <subscription_id>, {"count": 238}]
+["COUNT", <subscription_id>, {"count": <integer>, "hll": "<hex>"}]
 ```
 
+This is so it enables merging results from multiple relays and yielding a reasonable estimate of reaction counts, comment counts and follower counts, while saving many millions of bytes of bandwidth for everybody.
+
+### Algorithm
+
+This section describes the steps a relay should take in order to return HLL values to clients.
+
+1. Upon receiving a filter, if it has a single `#e`, `#p`, `#a` or `#q` item, read its 32th ascii character as a byte and take its modulo over 24 to obtain an `offset` -- in the unlikely case that the filter doesn't meet these conditions, set `offset` to the number 16;
+2. Initialize 256 registers to 0 for the HLL value;
+3. For all the events that are to be counted according to the filter, do this:
+    1. Read byte at position `offset` of the event `pubkey`, its value will be the register index `ri`;
+    2. Count the number of leading zero bits starting at position `offset+1` of the event `pubkey`;
+    3. Compare that with the value stored at register `ri`, if the new number is bigger, store it.
+
+That is all that has to be done on the relay side, and therefore the only part needed for interoperability.
+
+On the client side, these HLL values received from different relays can be merged (by simply going through all the registers in HLL values from each relay and picking the highest value for each register, regardless of the relay).
+
+And finally the absolute count can be estimated by running some methods I don't dare to describe here in English, it's better to check some implementation source code (also, there can be different ways of performing the estimation, with different quirks applied on top of the raw registers).
+
+### Attack vectors
+
+One could mine a pubkey with a certain number of zero bits in the exact place where the HLL algorithm described above would look for them in order to artificially make its reaction or follow "count more" than others. For this to work a different pubkey would have to be created for each different target (event id, followed profile etc). This approach is not very different than creating tons of new pubkeys and using them all to send likes or follow someone in order to inflate their number of followers. The solution is the same in both cases: clients should not fetch these reaction counts from open relays that accept everything, they should base their counts on relays that perform some form of filtering that makes it more likely that only real humans are able to publish there and not bots or artificially-generated pubkeys.
+
+### `hll` encoding
+
+The value `hll` value must be the concatenation of the 256 registers, each being a uint8 value (i.e. a byte). Therefore `hll` will be a 512-character hex string.
+
+## Examples
+
 ### Count posts and reactions
 
 ```
 ["COUNT", <subscription_id>, {"kinds": [1, 7], "authors": [<pubkey>]}]
 ["COUNT", <subscription_id>, {"count": 5}]
 ```
 
+
 ### Count posts approximately
 
 ```
 ["COUNT", <subscription_id>, {"kinds": [1]}]
 ["COUNT", <subscription_id>, {"count": 93412452, "approximate": true}]
 ```
 
+### Followers count with HyperLogLog
+
+```
+["COUNT", <subscription_id>, {"kinds": [3], "#p": [<pubkey>]}]
+["COUNT", <subscription_id>, {"count": 16578, "hll": "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"}]
+```
+
 ### Relay refuses to count
 
 ```