BMBurner is a Arduino based EPROM Programmer that can Read/Write/Verify Chips (27C256, SST 27SF512, W27E512, etc...)
- Windows Tool (BMBurner.exe) to Read/Write/Verify Chips
- Firmware Updating Tool to Update the BMBurner Firmware
- Driver for FTDI Chipset (BMBurner V1.1, V2.4 and Up, and Moates devices) : FTDI Driver
- Driver for CH340 Chipset (BMBurner V1.0, BMBurner V2.X) : CH340 Driver
- Download and Install the Firmware Updating Tool if not already done
- Open the Firmware Updating Tool
- Select the COM Port of your BMBurner (and the baudrate, default is 921600)
- Clic on 'Connect Device' button to connect to your BMBurner
- Clic on the 'Update Firmware' button!
If you have a BMBurner v2.5 or above, you must 'jump' the jumper nearby the Power Switch with a paperclip (by exemple) and at the same time than you are clicking on the 'Update Firmware' button otherwise the firmware won't install in the BMBurner
- 27C256 (Read-Only)
- 27C512 (Read-Only)
- 27SF256 (can only be burn with v2.4 and Up)
- 27SF512
- 27SF512 (Fake with 70ns access/write time)
- 29C256
- W27C512 (can only be burn with v2.0 and Up)
- W27E512 (can only be burn with v2.0 and Up)
- DS1230
- 61256/61C256
- 62256/62C256
*** Image may differ from the updated tool ***
- Load File to Buffer
- Save Buffer to File
- Read Chip
- Program Chip
- Verify Chip
- Blank Check
- Erase Chip
- Edit Reading/Writing Chip addressing
- Edit Reading/Writing Buffer addressing
- Much Mores...
| Command | Receice Buffer | Description |
|---|---|---|
| 'C'+R+'S'+'MSB'+'LSB'+'CS' | "B1"+"B2"+"...BX"+"CS" | Reads 'S' bytes(S=Size, S=0 for 256bytes) from the EEPROM at address 'MSB'+'LSB' (C=Chip, C=2 for 27C256, C=5 for 27SF512 SST) |
| 'C'+W+'S'+'MSB'+'LSB'+'B1'+'B2'+'...BX'+'CS' | "O"(0x4F) | Writes 'S' bytes(S=Size, S=0 for 256bytes) from the EEPROM at address 'MSB'+'LSB' (C=Chip, C=2 for 27C256, C=5 for 27SF512 SST) |
| 5+E+'CS' | "O"(0x4F) | Erase all the data on Chip Type 5 (SST) |
| 6+E+'CS' | "O"(0x4F) | Erase all the data on Chip Type 6 (SST 256) |
| V+'CS' (V+V) | "B1"+"B2" + "B3" | Prints the version bytes of the BMBurner PCB Board for Moates Compatibility(Ex:V5.1.0) |
| F+'CS' (F+F) | "B1"+"B2" | Prints the firmware bytes of the BMBurner PCB Board(Ex:V2.0) |
| G+'CS' (G+G) | "B1"+"B2" | Prints the BMBurner Starting baudrate (Ex:'B1=1,baud 921.6k', 'B1=2,baud 9600', 'B1=3,baud 115200') |
| S+0+S | "O"(0x4F) | Switch the internal baudrate on the BMBurner to 921600 for Moates Compatibility |
| S+7+S | "O"(0x4F) | Switch the internal baudrate on the BMBurner to 115600 for Moates Compatibility |
| A+'N' | "O"(0x4F) | Change the chip AccessTime to 'N'ns (Ex:N=70 for 70ns AccessTime) |
| Command | Descriptor |
|---|---|
| 'N' | 'N' equal the AccessTime in ns (Ex:N=70 for 70ns AccessTime) |
| 'MSB' | 'MSB' equal to the Most Signifiant Byte for the EEPROM Address location |
| 'LSB' | 'LSB' equal to the Least Signifiant Byte for the EEPROM Address location |
| 'C' | 'C' equel the Chip Type (C=2 for 27C256, C=5 for 27SF512 SST, C=6 for 27SF256 SST, etc..) |
| 'S' | 'S' equal the Size/Amount of bytes to proceed (S=0 is for 256bytes else S equal the amount of byte, S=1 for 1byte) |
| 'CS' | 'CS' equal to the checksum of the Commands we are sending in 1Byte form |
| ... | Any Command that isn't within 'Brackets' are the actual Char/String to send (ex: V is for sending the Char V |
You can donate to me using This Link.
