- 1. Mount IDM
- 2. Install IDM Klipper Module
- 3. Configure Klipper for IDM
- 4. Calibrate IDM
- 5. Basic First Tests
- 6. Calibrate Bed Mesh
- 7. Print
- 8. Enter High-Speed Mode
- 9. Enable The Accelerometer
- 10. Supported Commands
- 11. Update IDM
- 12. Set to USB
Mount the IDM-Scanner to your 3D printer toolhead, nominally 2.6mm recessed from the nozzle in Z.
To ensure accuracy, please install so that the top surface of the sensor coil plate is lower than the bottom surface of the heating block as much as possible.
Clone IDM from git and run the install script:
cd ~
git clone https://github.com/ModularPrintingSystem/IDM.git
./IDM/install.sh
You can advance to the next sections and edit your config files while you wait.
Add the idm configuration to your printer config:
[idm]
serial:
# Path to the serial port for the idm device. Typically has the form
# /dev/serial/by-id/usb-idm_idm_...
#canbus_uuid:
speed: 40.
# Z probing dive speed.
lift_speed: 5.
# Z probing lift speed.
backlash_comp: 0.5
# Backlash compensation distance for removing Z backlash before measuring
# the sensor response.
x_offset: 0.
# X offset of idm from the nozzle.
y_offset: 21.1
# Y offset of idm from the nozzle.
trigger_distance: 2.
# idm trigger distance for homing.
trigger_dive_threshold: 1.5
# Threshold for range vs dive mode probing. Beyond `trigger_distance +
# trigger_dive_threshold` a dive will be used.
trigger_hysteresis: 0.006
# Hysteresis on trigger threshold for untriggering, as a percentage of the
# trigger threshold.
cal_nozzle_z: 0.1
# Expected nozzle offset after completing manual Z offset calibration.
cal_floor: 0.1
# Minimum z bound on sensor response measurement.
cal_ceil:5.
# Maximum z bound on sensor response measurement.
cal_speed: 1.0
# Speed while measuring response curve.
cal_move_speed: 10.
# Speed while moving to position for response curve measurement.
default_model_name: default
# Name of default idm model to load.
mesh_main_direction: x
# Primary travel direction during mesh measurement.
#mesh_overscan: -1
# Distance to use for direction changes at mesh line ends. Omit this setting
# and a default will be calculated from line spacing and available travel.
mesh_cluster_size: 1
# Radius of mesh grid point clusters.
mesh_runs: 2
# Number of passes to make during mesh scan.
Please pay attention to the x-y offset in the adjustment configuration. Make sure that during the calibration process, the nozzle will move the coil to the x-y position of the original nozzle.
Remember to set [bed_mesh] otherwise an error will be reported.
Delete the [probe] module in your configuration and modify the z limit:
[stepper_z]
endstop_pin: probe:z_virtual_endstop # use idm as virtual endstop
homing_retract_dist: 0 # idm needs this to be set to 0
If you have already configured [safe_z_home] or [homing_override], you can ignore following step:
Set the safe x-y position for z homing (typically the bed center):
[safe_z_home]
home_xy_position: <your x-axis center>, <your y-axis center>
z_hop: 10
The serial query command is:
ls /dev/serial/by-id/*
Clone Katapult from git:
cd ~
git clone https://github.com/Arksine/katapult.git
To enable the canbus on the raspberry pi you need to create the interface file:
sudo nano /etc/network/interfaces.d/can0
And paste the following content:
allow-hotplug can0
iface can0 can static
bitrate 1000000
up ifconfig $IFACE txqueuelen 1024
To bring the canbus interface can0 up simply run:
sudo ifup can0
The canbus query command is:
python3 ~/katapult/scripts/flash_can.py -q
Home the machine in X and Y:
G28 X Y
Position the nozzle in the centre of the bed. You will nee dto adjust the coordinates for your machine, or feel free to use the web interface
G0 <your x-axis center>, <your y-axis center>
Start the calibration process:
IDM_CALIBRATE
Proceed through a standard nozzle paper offset test until the paper drags. Remove the paper and accept the position:
ACCEPT
The sensor response will be automatically measured and fit to a model. Save the results to your config file:
SAVE_CONFIG
You can take a spot measurement with IDM:
IDM_QUERY
Your Machine will home z with IDM:
G28 Z
You can test the accuracy:
PROBE_ACCURACY
You can measure the backlash of your Z axis:
IDM_ESTIMATE_BACKLASH
Run a scan mode mesh:
BED_MESH_CALIBRATE
You're now ready to print.
On the first print, you'll want to use babystepping via the GUI to fine adjust the first layer offset.
After the print finishes, the offset can be automatically applied to the model with Z_OFFSET_APPLY_PROBE command for future prints.
Lowering the horizontal_z_move in z_tilt or quad_gantry_level to below trigger_distance + trigger_dive_threshold (default is 3) can make the leveling enter high-speed mode. If it is too low, you can raise the trigger_dive_threshold appropriately so that horizontal_z_move can be raised higher.
For versions that include an accelerometer (lis2dw), you can enable the accelerometer by adding the following to the configuration:
[lis2dw]
cs_pin: idm:PA3
spi_bus: spi1
[resonance_tester]
accel_chip: lis2dw
probe_points:
<your x-axis center>, <your y-axis center>, 20
Enter IDM in the console and press the tab key to see all supported commands.
After IDM is connected to a power source, quickly unplug the power cord and plug it in again. The LED will start to flash slowly, indicating that it has entered canboot. If it is not successful, please repeat this step again.
Query IDM Canbus UUID:
python3 ~/klipper/lib/canboot/flash_can.py -q
Execute the following command:
cd ~/katapult/scripts python3 flashtool.py -i can0 -f ~/IDM/Canboot/Canboot_1M.bin -u <found uuid>
Query IDM Canbus UUID:
python3 ~/klipper/lib/canboot/flash_can.py -q
Execute the following command:
cd ~/katapult/scripts python3 flashtool.py -i can0 -f ~/IDM/Firmware/IDM_CAN_8kib_offset_1M.bin -u <found uuid>
If you want to change to USB communication, you can flash the USB firmware:
cd ~/katapult/scripts python3 flashtool.py -i can0 -f ~/IDM/Firmware/IDM_USB_8kib_offset.bin -u <found uuid>
And solder the mode setting jumper on the back of the IDM to the USB side.