SCV_Sensor_Settings.h

#ifndef __SCV_SENSOR_SETTINGS_H
#define __SCV_SENSOR_SETTINGS_H

#include "TI_LMP91000.h"
#include "eChem.h"

// Initial values for the algorithm used to convert ADC output into meaningful value
#define SENS_DENOM_0                            204800        // 2048 x 100  -- ADC resolution X
#define SENS_NUMER_0                            ECHEM_VDD * 100           // Voltage reference V x 100    
#define SENS_SUB_0                              ECHEM_VDD*0.5           
#define SENS_DENOM_1                            1400000        // R_TIA x 100
#define SENS_SCALE_FACTOR_NUM                   1000000   // Convert into ppm from nA
#define SENS_SCALE_FACTOR_DENOM                 1            // 70nA per ppm


// LMP91000 Settings for the OCP Sensor
#define SENS_OPERATIONAL_MODE                   OP_MODE_DEEP_SLEEP // 
#define SENS_FEEDBACK_GAIN                      TIA_GAIN_14K_OHM //
#define SENS_RLOAD                              R_LOAD_10_OHM // 
#define SENS_INT_Z_REF_DIVIDER                  INT_Z_SEL_50_PERCENT // 
#define SENS_REF_SOURCE                         REF_SOURCE_INTERNAL // Should cause no biasing of the electrodes
#define SENS_BIAS_SIGN                          BIAS_SIGN_NEGATIVE // Does not really matter what this is set to
#define SENS_BIAS_VOLTAGE                       BIAS_0_PERCENT  // Percentage of a floating input
#define SENS_FET_SHORT                          FET_SHORT_DISABLED

#define SENS_E_START                            BIAS_0_PERCENT // 
#define SENS_E_V1                               BIAS_24_PERCENT // 
#define SENS_SCANRATE                           100 // in ms

// Parameters used by iPhone/iPad app for graphing data
#define SENS_Y_DISPLAY_MAX                      2048
#define SENS_Y_DISPLAY_MIN                      1
#define SENS_GRAPH_TOP_MID_BOUNDARY             1848           // About 20% - Green - Yellow boundary
#define SENS_GRAPH_MID_LOW_BOUNDARY             200           // About 19% - Yellow - Red boundary
#define SENS_GRAPH_TOP_COLOR                    0x1B9E77      // Purple
#define SENS_GRAPH_MID_COLOR                    0x7075B3      // Green
#define SENS_GRAPH_LOW_COLOR                    0xD95F02      // Orange
#define SENS_CALIB                              1    // No Calibration
#define SENS_TYPE                               CHILI_SENSOR_TYPE    
#define SENS_DISPLAY_CURRENT_VALUE              1            // Display current value
#define SENS_DISPLAY_LOG_SCALE                  0             // Do not use logarithmic scale


// Note that 19 character maximum for Characteristic strings, that is 18 characters + \0!!!
#define SENS_GRAPH_TITLE                        "Multistep Amperom.\0"
#define SENS_GRAPH_TITLE_SIZE                   19
#define SENS_GRAPH_SUBTITLE                     "Using the LMP91000\0"
#define SENS_GRAPH_SUBTITLE_SIZE                19
#define SENS_GRAPH_X_AXIS_CAPTION               "Time / s \0"
#define SENS_GRAPH_X_AXIS_CAPTION_SIZE          10
#define SENS_GRAPH_Y_AXIS_CAPTION               "Current / uA \0"    
#define SENS_GRAPH_Y_AXIS_CAPTION_SIZE          14
#define SENS_SHORT_CAPTION_VALUE                "MA\0"
#define SENS_SHORT_CAPTION_SIZE                 3

#endif // __SCV_SENSOR_SETTINGS_H