Replies: 6 comments 8 replies
-
|
I'm actually trying to do something similar this weekend. I can't seem to get an IP link for longer than a few seconds. I get the error 619 consistently. Any ideas what that may be pointing to? I'm in the GTA. Please share the following output with the developers: |
Beta Was this translation helpful? Give feedback.
-
|
I am not sure what is going on. I had it working on a edge router but decided to try this. But would lose picture after a couple minutes. I put back the Edge router with no changes and getting the same thing. Something changed but not sure what
i do notice you are getting the same thing like me
10.117.160.0/20 proto kernel scope link src 10.117.166.37
the ip subnets don't match. they used to but not anymore
…________________________________
From: dP210 ***@***.***>
Sent: Friday, August 9, 2024 9:59:42 PM
To: fabianishere/udm-iptv ***@***.***>
Cc: Mark Chong ***@***.***>; Author ***@***.***>
Subject: Re: [fabianishere/udm-iptv] Bell TV (Discussion #345)
I'm actually trying to do something similar this weekend.
I can't seem to get an IP link for longer than a few seconds. I get the error 619 consistently. Any ideas what that may be pointing to? I'm in the GTA.
lease share the following output with the developers:
=== Configuration ===
WAN Interface: eth9
WAN VLAN: 36 (dev iptv)
WAN DHCP: true (options "-o")
WAN Ranges: 10.2.0.0/16 10.125.0.0/16 10.117.0.0/16
LAN Interfaces: br100
IGMP Proxy quickleave disabled: false
IGMP Proxy debug: true
=== IP Link and Route ===
19298: ***@***.***: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
inet 10.117.166.37/20 scope global iptv
valid_lft forever preferred_lft forever
10.117.160.0/20 proto kernel scope link src 10.117.166.37
=== Service Logs ===
Aug 09 21:51:20 Dream-Machine-Pro udm-iptvd[3991790]: ***@***.***: if_index = 18007
Aug 09 21:51:20 Dream-Machine-Pro udm-iptvd[3991790]: ***@***.***: if_mtu = 1500
Aug 09 21:51:20 Dream-Machine-Pro udm-iptvd[3991790]: ***@***.***: if_falgs = 4163
Aug 09 21:51:20 Dream-Machine-Pro udm-iptvd[3991790]: ***@***.***: iptv's ipv4 address is 10.117.166.37
Aug 09 21:51:20 Dream-Machine-Pro udm-iptvd[3991790]: ***@***.***: if_index = 19298
Aug 09 21:51:20 Dream-Machine-Pro udm-iptvd[3991790]: ***@***.***: if_mtu = 1500
Aug 09 21:51:20 Dream-Machine-Pro udm-iptvd[3991790]: ***@***.***: if_falgs = 4163
Aug 09 21:51:20 Dream-Machine-Pro udm-iptvd[3991790]: ***@***.***: exiting.........
—
Reply to this email directly, view it on GitHub<#345 (comment)>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/AXT6FSLARBG64Q7FG7NQXJTZQVXY5AVCNFSM6AAAAABMI4UNBKVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTAMRZGI3TIMY>.
You are receiving this because you authored the thread.Message ID: ***@***.***>
|
Beta Was this translation helpful? Give feedback.
-
|
I too had an Edgerouter set up for the longest time but got myself a UDM Pro a few months back and only recently stumbled upon Fabian's solution. So this morning I played with it a bit more and was able to get it up and running. The one thing I think may have helped was after I read this thread from some time ago and the VLAN's needing to be applied to a switch port profile. So I modified my local VLAN that connected to my STB and applied the Tagged Networks with both VLAN 35 and 36. The way to do that with current UDM OS is switching to the 'old' interface AFAIK. It's been running for about 2 hours and recorded to PVR. Fingers crossed it stays up! |
Beta Was this translation helpful? Give feedback.
-
|
can you post your diag and what you did for the static route |
Beta Was this translation helpful? Give feedback.
-
|
I added your tagging, but still losing signal after a couple minute. |
Beta Was this translation helpful? Give feedback.
-
|
if you can also post your UDM settings, I am missing something but can't think of it |
Beta Was this translation helpful? Give feedback.
-
|
I am getting this Please share the following output with the developers: |
Beta Was this translation helpful? Give feedback.
-
|
Here's my Config: For UDM, I have 2 VLAN only networks, 35 and 36 which are tagged on the VLAN for my LAN IPTV connection. In my case VLAN 100. For the VLAN 100 network, I have also put in the DNS servers I've seen posted online. I probably have extra DNS Of course IGMP snooping enabled on the VLAN 100 network. It is weird that there is the mismatch of the subnet for the static routes. I'm hoping it stays up with a reboot which I've yet to try. Also I did connect the HH3000 and hardwired the 4K receiver last night while I was fiddling with the settings to get the receiver back on LAN connectivity since it was trying to establish via WiFi (WPS setting screen was showing). === Configuration === |
Beta Was this translation helpful? Give feedback.
-
|
weird this is my UDM
|
Beta Was this translation helpful? Give feedback.
-
|
can you show me what you put for this For the VLAN 100 network, I have also put in the DHCP servers I've seen posted online. I probably have extra DHCP servers in there, and could clean up. |
Beta Was this translation helpful? Give feedback.
-
|
I've updated my post with the DNS servers. Also you need to put the VLAN 35/36 on the Switch Port profile in the legacy UI. |
Beta Was this translation helpful? Give feedback.
-
|
i created a profile
still only works for a couple seconds |
Beta Was this translation helpful? Give feedback.
-
|
got it working needed to turn on IGMP snooping on the vlan 35 and 36
I knew is was something stupid i was missing |
Beta Was this translation helpful? Give feedback.
-
Awesome! Hoping this stays working for an extended period of time and works through reboots. Fingers crossed. |
Beta Was this translation helpful? Give feedback.
-
I have set this up again, and everything looks good but the after a new seconds I lose picture again.
here is my udm-iptv diag
Please share the following output with the developers:
=== Configuration ===
WAN Interface: eth9
WAN VLAN: 36 (dev iptv)
WAN DHCP: true (options "-n -o")
WAN Ranges: 10.2.0.0/16 10.238.0.0/16
LAN Interfaces: br40
IGMP Proxy quickleave disabled: false
IGMP Proxy debug: false
=== IP Link and Route ===
71: iptv@eth9: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
inet 10.238.130.204/22 scope global iptv
valid_lft forever preferred_lft forever
10.2.0.0/16 via 10.238.128.1
10.238.0.0/16 via 10.238.128.1
10.238.128.0/22 proto kernel scope link src 10.238.130.204
=== Service Logs ===
Aug 09 13:49:02 Hollingsworth udm-iptvd[3509851]: Obtaining IP address for VLAN interface
Aug 09 13:49:02 Hollingsworth udm-iptvd[3509885]: udhcpc: started, v1.30.1
Aug 09 13:49:02 Hollingsworth udm-iptvd[3509885]: udhcpc: sending discover
Aug 09 13:49:02 Hollingsworth udm-iptvd[3509885]: udhcpc: sending select for 10.238.130.204
Aug 09 13:49:02 Hollingsworth udm-iptvd[3509885]: udhcpc: lease of 10.238.130.204 obtained, lease time 603523
Aug 09 13:49:03 Hollingsworth udm-iptvd[3509851]: NATing IPTV network ranges (if necessary)
Aug 09 13:49:03 Hollingsworth udm-iptvd[3509851]: Creating static routes (if necessary)
Aug 09 13:49:03 Hollingsworth udm-iptvd[3509851]: Setting up IGMP Proxy
Aug 09 13:49:03 Hollingsworth udm-iptvd[3509851]: Using improxy...
Aug 09 13:49:03 Hollingsworth udm-iptvd[3509851]: Starting IGMP Proxy
only thing i see that is i weird is this
10.238.128.0/22 proto kernel scope link src 10.238.130.204
everyone elses diag doesn't have this.
any thoughts?
Beta Was this translation helpful? Give feedback.
All reactions