compile-all-combinations.yml

# This is the name of the workflow, visible on GitHub UI.
name: Compile All Combinations

# Here we tell GitHub when to run the workflow.
on:
  # This allows you to run this workflow manually from the
  # GitHub Actions tab.
  workflow_dispatch:
  # The workflow is run upon creating, editing,
  # pre-releasing, releasing and publishing a release
  release:
    types: [created, edited, prereleased, released, published]

# This is the list of jobs that will be run concurrently.
# Since we use a build matrix, the actual number of jobs
# started depends on how many configurations the matrix
# will produce.
jobs:
  # This is the name of the job.
  build-matrix:

    # Here we tell GitHub that the jobs must be determined
    # dynamically depending on a matrix configuration.
    strategy:
      # The matrix will produce one job for each combination of parameters.
      matrix:
        # This is the development board hardware for which the code will be compiled.
        # FBQN stands for "fully qualified board name", and is used by Arduino to define the hardware to compile for.
        fqbn:
          - esp32:esp32:esp32
          # further ESP32 chips
          #- esp32:esp32:esp32c3
          #- esp32:esp32:esp32c2
          #- esp32:esp32:esp32c6
          #- esp32:esp32:esp32h2
          #- esp32:esp32:esp32s3
        # These are the batteries for which the code will be compiled.
        battery:
          - BMW_I3_BATTERY
          - BMW_IX_BATTERY
          - BYD_ATTO_3_BATTERY
          - CELLPOWER_BMS
          - CHADEMO_BATTERY
          - IMIEV_CZERO_ION_BATTERY
          - JAGUAR_IPACE_BATTERY
          - KIA_E_GMP_BATTERY
          - KIA_HYUNDAI_64_BATTERY
          - KIA_HYUNDAI_HYBRID_BATTERY
          - MEB_BATTERY
          - MG_5_BATTERY
          - NISSAN_LEAF_BATTERY
          - PYLON_BATTERY
          - RJXZS_BMS
          - RANGE_ROVER_PHEV_BATTERY
          - RENAULT_KANGOO_BATTERY
          - RENAULT_TWIZY_BATTERY
          - RENAULT_ZOE_GEN1_BATTERY
          - RENAULT_ZOE_GEN2_BATTERY
          - SANTA_FE_PHEV_BATTERY
          - TESLA_MODEL_3Y_BATTERY
          - TESLA_MODEL_SX_BATTERY
          - VOLVO_SPA_BATTERY
          - TEST_FAKE_BATTERY
        # These are the emulated inverter communication protocols for which the code will be compiled.
        inverter:
          - AFORE_CAN
          - BYD_CAN
          - BYD_KOSTAL_RS485
          - BYD_MODBUS
          - BYD_SMA
          - FOXESS_CAN
          - PYLON_CAN
          - PYLON_LV_CAN
          - SCHNEIDER_CAN
          - SMA_CAN
          - SMA_LV_CAN
          - SMA_TRIPOWER_CAN
          - SOFAR_CAN
          - SOLAX_CAN
          - SERIAL_LINK_TRANSMITTER

    # This is the platform GitHub will use to run our workflow.
    runs-on: ubuntu-latest

    # This is the list of steps this job will run.
    steps:
      # First we clone the repo using the `checkout` action.
      - name: Checkout
        uses: actions/checkout@v4

      # We use the `arduino/setup-arduino-cli` action to install and
      # configure the Arduino CLI on the system.
      - name: Setup Arduino CLI
        uses: arduino/setup-arduino-cli@v2

      # We then install the platform.
      - name: Install platform
        run: |
          arduino-cli core update-index
          arduino-cli core install esp32:esp32

      # Finally, we compile the sketch, using the FQBN that was set
      # in the build matrix, and using build flags to define the
      # battery and inverter set in the build matrix.
      - name: Compile Sketch
        run: arduino-cli compile --fqbn ${{ matrix.fqbn }} --build-property "build.extra_flags=-Wall -DESP32 -D${{ matrix.battery}} -D${{ matrix.inverter}}" ./Software