Purple-printer.cfg

###### Creality Ender3 (2018) with SKR v1.3 and BLTocuh and TMC2130SPI on XYXE #####
#[include D3_Initial Setup.txt]
#[include D3_BLTouch.txt]
#[include D3_SensorlessHoming.txt]
#[include fluidd.cfg]
#[include D3_Macros.cfg]


[include fluidd.cfg]
[include kiauh_macros.cfg]
#[include PA_Tuner.cfg]
[include D3_Initial Setup.cfg]
[include D3_Macros.cfg]
[include D3_BLTouchMacro.cfg]
[exclude_object]
#[include adxl345.cfg]

# This file contains common pin mappings for the BIGTREETECH SKR V1.3
# board. To use this config, the firmware should be compiled for the
# LPC1768.

# See docs/Config_Reference.md for a description of parameters.

[stepper_x]
step_pin: P2.2
dir_pin: !P2.6
enable_pin: !P2.1
microsteps: 16
rotation_distance: 40
endstop_pin: P1.29  # P1.28 for X-max
position_endstop: 0
position_max: 235
homing_speed: 200.0
homing_retract_dist: 0

[stepper_y]
step_pin: P0.19
dir_pin: !P0.20
enable_pin: !P2.8
microsteps: 16
rotation_distance: 40
endstop_pin: P1.27  # P1.26 for Y-max
position_endstop: 0
position_max: 240
homing_speed: 200.0
homing_retract_dist: 0

[stepper_z]
step_pin: P0.22
dir_pin: P2.11
enable_pin: !P0.21
microsteps: 16
rotation_distance: 8
#endstop_pin: P1.25  # P1.24 for Z-max
endstop_pin: probe:z_virtual_endstop
#position_endstop: 0.0
position_min: -15
position_max: 350
homing_speed: 100
second_homing_speed: 2

[extruder]
max_extrude_only_distance: 100.0
step_pin: P2.13
#dir_pin: !P0.11  Normal Ender 3, mine is backwards because I used a different cable.
dir_pin: P0.11
enable_pin: !P2.12
microsteps: 16
rotation_distance: 33.683
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: P2.7
sensor_type: EPCOS 100K B57560G104F
sensor_pin: P0.24
control: pid
pid_Kp: 21.527
pid_Ki: 1.063
pid_Kd: 108.982
min_temp: 0
max_temp: 270


#pressure_advance = <measured_height> * <factor> 

#16mm * 0.005 = 0.08
#15mm * 0.005 = 0.075 
#14mm * 0.005 = 0.07
#13mm * 0.005 =0.065
pressure_advance = 0.08

#[extruder1]
#step_pin: P0.1
#dir_pin: P0.0
#enable_pin: !P0.10
#heater_pin: P2.4
#sensor_pin: P0.25
#...

[heater_bed]
heater_pin: P2.5
sensor_type: EPCOS 100K B57560G104F
sensor_pin: P0.23
control: pid
# tuned for stock hardware with 50 degree Celsius target
pid_Kp: 54.027
pid_Ki: 0.770
pid_Kd: 948.182
min_temp: 0
max_temp: 130


[fan]
pin: P2.3

[heater_fan extruder_fan]
pin: P2.4
heater: extruder
#   Name of the config section defining the heater that this fan is
#   associated with. If a comma separated list of heater names is
#   provided here, then the fan will be enabled when any of the given
#   heaters are enabled. The default is "extruder".
heater_temp: 50.0
#   A temperature (in Celsius) that the heater must drop below before
#   the fan is disabled. The default is 50 Celsius.
fan_speed: 1.0
#   The fan speed (expressed as a value from 0.0 to 1.0) that the fan
#   will be set to when its associated heater is enabled. The default
#   is 1.0

[mcu]
serial: /dev/serial/by-id/usb-Klipper_lpc1768_0890FF10031436AF68F46A5BC32000F5-if00

[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 3000
max_z_velocity: 5
max_z_accel: 100

########################################
# TMC2208 configuration
########################################

# For TMC2208 UART
#   1) Remove all of the jumpers below the stepper drivers
#   2) Place jumpers on the red pin headers labeled XUART (XUART, YUART etc.)

#[tmc2208 stepper_x]
#uart_pin: P1.17
#run_current: 0.800
#stealthchop_threshold: 999999

#[tmc2208 stepper_y]
#uart_pin: P1.15
#run_current: 0.800
#stealthchop_threshold: 999999

#[tmc2208 stepper_z]
#uart_pin: P1.10
#run_current: 0.650
#stealthchop_threshold: 999999

#[tmc2208 extruder]
#uart_pin: P1.8
#run_current: 0.800
#stealthchop_threshold: 999999

#[tmc2208 extruder1]
#uart_pin: P1.1
#run_current: 0.800
#stealthchop_threshold: 999999


########################################
# TMC2130 configuration
########################################

# For TMC SPI
#   1) Place jumpers on all the red pin headers under the stepper drivers
#   2) Remove jumpers from the red pin headers labeled XUART (XUART, YUART etc.)

[tmc2130 stepper_x]
cs_pin: P1.17
spi_software_miso_pin: P0.5
spi_software_mosi_pin: P4.28
spi_software_sclk_pin: P0.4
diag1_pin: P1.29
#run_current: 0.800
run_current: 0.725 
#stealthchop_threshold: 999999

[tmc2130 stepper_y]
cs_pin: P1.15
spi_software_miso_pin: P0.5
spi_software_mosi_pin: P4.28
spi_software_sclk_pin: P0.4
diag1_pin: P1.27
#run_current: 0.800
run_current: 0.725
#stealthchop_threshold: 999999

[tmc2130 stepper_z]
cs_pin: P1.10
spi_software_miso_pin: P0.5
spi_software_mosi_pin: P4.28
spi_software_sclk_pin: P0.4
diag1_pin: P1.25
run_current: 0.725
#stealthchop_threshold: 999999

[tmc2130 extruder]
cs_pin: P1.8
spi_software_miso_pin: P0.5
spi_software_mosi_pin: P4.28
spi_software_sclk_pin: P0.4
diag1_pin: P1.28
run_current: 0.725
#stealthchop_threshold: 999999

#[tmc2130 extruder1]
#cs_pin: P1.1
#spi_software_miso_pin: P0.5
#spi_software_mosi_pin: P4.28
#spi_software_sclk_pin: P0.4
##diag1_pin: P1.26
#run_current: 0.800
#stealthchop_threshold: 999999


########################################
# EXP1 / EXP2 (display) pins
########################################

[board_pins]
aliases:
    # EXP1 header
    EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
    EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
    # EXP2 header
    EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
    EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
    # Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "ssp0"

# See the sample-lcd.cfg file for definitions of common LCD displays.

########################################
# Ender 3 Display
########################################

[display]
lcd_type: st7920
cs_pin: EXP1_7
sclk_pin: EXP1_6
sid_pin: EXP1_8
encoder_pins: ^EXP1_5, ^EXP1_3
click_pin: ^!EXP1_2

#[output_pin beeper]
#pin: EXP1_1

########################################
# Ender 3 Display
########################################

[output_pin BEEPER_pin]
pin: EXP1_1
#   Beeper pin. This parameter must be provided.
#   ar37 is the default RAMPS/MKS pin.
pwm: True
#   A piezo beeper needs a PWM signal, a DC buzzer doesn't.
value: 0
#   Silent at power on, set to 1 if active low.
shutdown_value: 0
#   Disable at emergency shutdown (no PWM would be available anyway).
cycle_time: 0.001
#   Default PWM frequency : 0.001 = 1ms will give a tone of 1kHz
#   Although not pitch perfect.

[gcode_macro M300]
gcode:
    # Use a default 1kHz tone if S is omitted.
    {% set S = params.S|default(1000)|int %}
    # Use a 10ms duration is P is omitted.
    {% set P = params.P|default(1000)|int %}
    SET_PIN PIN=BEEPER_pin VALUE=0.5 CYCLE_TIME={ 1.0/S if S > 0 else 1 }
    G4 P{P}
    SET_PIN PIN=BEEPER_pin VALUE=0

[bltouch]
#sensor_pin: ^P1.25   # Pull-up (^ symbol) needed in open drain mode
sensor_pin: ^P1.25   # Pull-up (^ symbol) needed in open drain mode
control_pin: P2.0
pin_up_touch_mode_reports_triggered: False
x_offset: -44
y_offset: -14
#z_offset: 1
speed: 30.0
samples: 1
sample_retract_dist: 8.0
samples_result:median

[safe_z_home]
home_xy_position: 161,131
speed: 200.0
z_hop: 15
z_hop_speed: 15

# This adds a bed mesh calibrate GCode
[bed_mesh]
speed: 200.0
mesh_min: 50, 10
mesh_max: 190, 190
horizontal_move_z: 15
probe_count: 3,3
mesh_pps: 0 ;disable mesh interpolation (fixes issues with Bed Visualizer plug-in)

[screws_tilt_adjust]
#   The (X, Y) coordinate of the first bed leveling screw.
screw1: 75, 210
screw2: 235, 210
screw3: 235, 40
screw4: 75, 40
speed: 150.0
#   The speed (in mm/s) of non-probing moves during the calibration.
#   The default is 50.
horizontal_move_z: 15
screw_thread: CW-M4

# z_offset = 2.325

#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [bltouch]
#*# z_offset = 2.600
#*#
#*# [input_shaper]
#*# shaper_type_x = zv
#*# shaper_freq_x = 123.2
#*# shaper_type_y = 2hump_ei
#*# shaper_freq_y = 41.2
#*#
#*# [bed_mesh default]
#*# version = 1
#*# points =
#*# 	  0.025000, 0.002500, -0.052500
#*# 	  0.185000, -0.005000, 0.027500
#*# 	  0.235000, 0.015000, 0.137500
#*# tension = 0.2
#*# min_x = 50.0
#*# algo = lagrange
#*# y_count = 3
#*# mesh_y_pps = 0
#*# min_y = 10.0
#*# x_count = 3
#*# max_y = 190.0
#*# mesh_x_pps = 0
#*# max_x = 190.0