diff --git a/resources/profiles/Elegoo/machine/Elegoo Neptune 4 (0.2 nozzle).json b/resources/profiles/Elegoo/machine/Elegoo Neptune 4 (0.2 nozzle).json index ec108f4bbc5..a89e82d0216 100644 --- a/resources/profiles/Elegoo/machine/Elegoo Neptune 4 (0.2 nozzle).json +++ b/resources/profiles/Elegoo/machine/Elegoo Neptune 4 (0.2 nozzle).json @@ -45,13 +45,13 @@ "45" ], "single_extruder_multi_material": "1", - "change_filament_gcode": "PAUSE", - "machine_pause_gcode": "M0", + "change_filament_gcode": "M600", + "machine_pause_gcode": "PAUSE", "default_filament_profile": [ "Elegoo Generic PLA @0.2 nozzle" ], - "machine_start_gcode": "M413 S0 ; disable Power Loss Recovery\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S120 ; set temporary nozzle temp to prevent oozing during homing and auto bed leveling\nM140 S[bed_temperature_initial_layer_single] ; set final bed temp\nG4 S10 ; allow partial nozzle warmup\nG28 ; home all axis\n;G29 ; run abl mesh\nM420 S1 ; load mesh\nG1 Z50 F240\nG1 X2 Y10 F3000\n\nM190 S[bed_temperature_initial_layer_single] ; wait for bed temp to stabilize\nM109 S[nozzle_temperature_initial_layer] ; wait for nozzle temp to stabilize\nG1 Z0.28 F240\nG92 E0\nG1 Y140 E10 F1500 ; prime the nozzle\nG1 X2.3 F5000\nG92 E0\nG1 Y10 E10 F1200 ; prime the nozzle\nG92 E0", - "machine_end_gcode": "{if max_layer_z < printable_height}G1 Z{z_offset+min(max_layer_z+2, printable_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.8} F{travel_speed*60} ; present print\n{if max_layer_z < printable_height-10}G1 Z{z_offset+min(max_layer_z+70, printable_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < printable_height*0.6}G1 Z{printable_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors", + "machine_start_gcode": ";ELEGOO NEPTUNE 4\nM220 S100 ;Set the feed speed to 100%\nM221 S100 ;Set the flow rate to 100%\nM104 S140\nM190 S[bed_temperature_initial_layer_single]\nG90\nG28 ;home\nG1 Z10 F300\nG1 X67.5 Y0 F6000\nG1 Z0 F300\nM109 S[nozzle_temperature_initial_layer]\nG92 E0 ;Reset Extruder\nG1 X67.5 Y0 Z0.4 F300 ;Move to start position\nG1 X167.5 E30 F400 ;Draw the first line\nG1 Z0.6 F120.0 ;Move to side a little\nG1 X162.5 F3000\nG92 E0 ;Reset Extruder\n", + "machine_end_gcode": ";PRINT_END\nG91 ;Relative positionning\nG1 E-2 F2700 ;Retract a bit\nG1 E-8 X5 Y5 Z3 F3000 ;Retract\nG90 ;Absolute positionning\nG1 X10 Y220 F6000;Finish print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z", "before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\nG92 E0\n;[layer_z]\n\n", "layer_change_gcode": ";AFTER_LAYER_CHANGE\n;[layer_z]", "scan_first_layer": "0" diff --git a/resources/profiles/Elegoo/machine/Elegoo Neptune 4 (0.4 nozzle).json b/resources/profiles/Elegoo/machine/Elegoo Neptune 4 (0.4 nozzle).json index 31f286183ab..2717448e779 100644 --- a/resources/profiles/Elegoo/machine/Elegoo Neptune 4 (0.4 nozzle).json +++ b/resources/profiles/Elegoo/machine/Elegoo Neptune 4 (0.4 nozzle).json @@ -45,13 +45,13 @@ "45" ], "single_extruder_multi_material": "1", - "change_filament_gcode": "PAUSE", - "machine_pause_gcode": "M0", + "change_filament_gcode": "M600", + "machine_pause_gcode": "PAUSE", "default_filament_profile": [ "Elegoo Generic PLA @0.4 nozzle" ], - "machine_start_gcode": "M413 S0 ; disable Power Loss Recovery\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S120 ; set temporary nozzle temp to prevent oozing during homing and auto bed leveling\nM140 S[bed_temperature_initial_layer_single] ; set final bed temp\nG4 S10 ; allow partial nozzle warmup\nG28 ; home all axis\n;G29 ; run abl mesh\nM420 S1 ; load mesh\nG1 Z50 F240\nG1 X2 Y10 F3000\n\nM190 S[bed_temperature_initial_layer_single] ; wait for bed temp to stabilize\nM109 S[nozzle_temperature_initial_layer] ; wait for nozzle temp to stabilize\nG1 Z0.28 F240\nG92 E0\nG1 Y140 E10 F1500 ; prime the nozzle\nG1 X2.3 F5000\nG92 E0\nG1 Y10 E10 F1200 ; prime the nozzle\nG92 E0", - "machine_end_gcode": "{if max_layer_z < printable_height}G1 Z{z_offset+min(max_layer_z+2, printable_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.8} F{travel_speed*60} ; present print\n{if max_layer_z < printable_height-10}G1 Z{z_offset+min(max_layer_z+70, printable_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < printable_height*0.6}G1 Z{printable_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors", + "machine_start_gcode": ";ELEGOO NEPTUNE 4\nM220 S100 ;Set the feed speed to 100%\nM221 S100 ;Set the flow rate to 100%\nM104 S140\nM190 S[bed_temperature_initial_layer_single]\nG90\nG28 ;home\nG1 Z10 F300\nG1 X67.5 Y0 F6000\nG1 Z0 F300\nM109 S[nozzle_temperature_initial_layer]\nG92 E0 ;Reset Extruder\nG1 X67.5 Y0 Z0.4 F300 ;Move to start position\nG1 X167.5 E30 F400 ;Draw the first line\nG1 Z0.6 F120.0 ;Move to side a little\nG1 X162.5 F3000\nG92 E0 ;Reset Extruder\n", + "machine_end_gcode": ";PRINT_END\nG91 ;Relative positionning\nG1 E-2 F2700 ;Retract a bit\nG1 E-8 X5 Y5 Z3 F3000 ;Retract\nG90 ;Absolute positionning\nG1 X10 Y220 F6000;Finish print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z", "before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\nG92 E0\n;[layer_z]\n\n", "layer_change_gcode": ";AFTER_LAYER_CHANGE\n;[layer_z]", "scan_first_layer": "0" diff --git a/resources/profiles/Elegoo/machine/Elegoo Neptune 4 (0.6 nozzle).json b/resources/profiles/Elegoo/machine/Elegoo Neptune 4 (0.6 nozzle).json index 25719258317..693ff8d3702 100644 --- a/resources/profiles/Elegoo/machine/Elegoo Neptune 4 (0.6 nozzle).json +++ b/resources/profiles/Elegoo/machine/Elegoo Neptune 4 (0.6 nozzle).json @@ -45,13 +45,13 @@ "45" ], "single_extruder_multi_material": "1", - "change_filament_gcode": "PAUSE", - "machine_pause_gcode": "M0", + "change_filament_gcode": "M600", + "machine_pause_gcode": "PAUSE", "default_filament_profile": [ "Elegoo Generic PLA @0.6 nozzle" ], - "machine_start_gcode": "M413 S0 ; disable Power Loss Recovery\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S120 ; set temporary nozzle temp to prevent oozing during homing and auto bed leveling\nM140 S[bed_temperature_initial_layer_single] ; set final bed temp\nG4 S10 ; allow partial nozzle warmup\nG28 ; home all axis\n;G29 ; run abl mesh\nM420 S1 ; load mesh\nG1 Z50 F240\nG1 X2 Y10 F3000\n\nM190 S[bed_temperature_initial_layer_single] ; wait for bed temp to stabilize\nM109 S[nozzle_temperature_initial_layer] ; wait for nozzle temp to stabilize\nG1 Z0.28 F240\nG92 E0\nG1 Y140 E10 F1500 ; prime the nozzle\nG1 X2.3 F5000\nG92 E0\nG1 Y10 E10 F1200 ; prime the nozzle\nG92 E0", - "machine_end_gcode": "{if max_layer_z < printable_height}G1 Z{z_offset+min(max_layer_z+2, printable_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.8} F{travel_speed*60} ; present print\n{if max_layer_z < printable_height-10}G1 Z{z_offset+min(max_layer_z+70, printable_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < printable_height*0.6}G1 Z{printable_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors", + "machine_start_gcode": ";ELEGOO NEPTUNE 4\nM220 S100 ;Set the feed speed to 100%\nM221 S100 ;Set the flow rate to 100%\nM104 S140\nM190 S[bed_temperature_initial_layer_single]\nG90\nG28 ;home\nG1 Z10 F300\nG1 X67.5 Y0 F6000\nG1 Z0 F300\nM109 S[nozzle_temperature_initial_layer]\nG92 E0 ;Reset Extruder\nG1 X67.5 Y0 Z0.4 F300 ;Move to start position\nG1 X167.5 E30 F400 ;Draw the first line\nG1 Z0.6 F120.0 ;Move to side a little\nG1 X162.5 F3000\nG92 E0 ;Reset Extruder\n", + "machine_end_gcode": ";PRINT_END\nG91 ;Relative positionning\nG1 E-2 F2700 ;Retract a bit\nG1 E-8 X5 Y5 Z3 F3000 ;Retract\nG90 ;Absolute positionning\nG1 X10 Y220 F6000;Finish print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z", "before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\nG92 E0\n;[layer_z]\n\n", "layer_change_gcode": ";AFTER_LAYER_CHANGE\n;[layer_z]", "scan_first_layer": "0" diff --git a/resources/profiles/Elegoo/machine/Elegoo Neptune 4 (0.8 nozzle).json b/resources/profiles/Elegoo/machine/Elegoo Neptune 4 (0.8 nozzle).json index be0547eff2a..ab3fbb9b4af 100644 --- a/resources/profiles/Elegoo/machine/Elegoo Neptune 4 (0.8 nozzle).json +++ b/resources/profiles/Elegoo/machine/Elegoo Neptune 4 (0.8 nozzle).json @@ -45,13 +45,13 @@ "45" ], "single_extruder_multi_material": "1", - "change_filament_gcode": "PAUSE", - "machine_pause_gcode": "M0", + "change_filament_gcode": "M600", + "machine_pause_gcode": "PAUSE", "default_filament_profile": [ "Elegoo Generic PLA @0.8 nozzle" ], - "machine_start_gcode": "M413 S0 ; disable Power Loss Recovery\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S120 ; set temporary nozzle temp to prevent oozing during homing and auto bed leveling\nM140 S[bed_temperature_initial_layer_single] ; set final bed temp\nG4 S10 ; allow partial nozzle warmup\nG28 ; home all axis\n;G29 ; run abl mesh\nM420 S1 ; load mesh\nG1 Z50 F240\nG1 X2 Y10 F3000\n\nM190 S[bed_temperature_initial_layer_single] ; wait for bed temp to stabilize\nM109 S[nozzle_temperature_initial_layer] ; wait for nozzle temp to stabilize\nG1 Z0.28 F240\nG92 E0\nG1 Y140 E10 F1500 ; prime the nozzle\nG1 X2.3 F5000\nG92 E0\nG1 Y10 E10 F1200 ; prime the nozzle\nG92 E0", - "machine_end_gcode": "{if max_layer_z < printable_height}G1 Z{z_offset+min(max_layer_z+2, printable_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.8} F{travel_speed*60} ; present print\n{if max_layer_z < printable_height-10}G1 Z{z_offset+min(max_layer_z+70, printable_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < printable_height*0.6}G1 Z{printable_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors", + "machine_start_gcode": ";ELEGOO NEPTUNE 4\nM220 S100 ;Set the feed speed to 100%\nM221 S100 ;Set the flow rate to 100%\nM104 S140\nM190 S[bed_temperature_initial_layer_single]\nG90\nG28 ;home\nG1 Z10 F300\nG1 X67.5 Y0 F6000\nG1 Z0 F300\nM109 S[nozzle_temperature_initial_layer]\nG92 E0 ;Reset Extruder\nG1 X67.5 Y0 Z0.4 F300 ;Move to start position\nG1 X167.5 E30 F400 ;Draw the first line\nG1 Z0.6 F120.0 ;Move to side a little\nG1 X162.5 F3000\nG92 E0 ;Reset Extruder\n", + "machine_end_gcode": ";PRINT_END\nG91 ;Relative positionning\nG1 E-2 F2700 ;Retract a bit\nG1 E-8 X5 Y5 Z3 F3000 ;Retract\nG90 ;Absolute positionning\nG1 X10 Y220 F6000;Finish print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z", "before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\nG92 E0\n;[layer_z]\n\n", "layer_change_gcode": ";AFTER_LAYER_CHANGE\n;[layer_z]", "scan_first_layer": "0" diff --git a/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Max (0.2 nozzle).json b/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Max (0.2 nozzle).json index fd0f4d3b309..ba0d8ddba46 100644 --- a/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Max (0.2 nozzle).json +++ b/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Max (0.2 nozzle).json @@ -75,13 +75,13 @@ "wipe_distance": ["1"], "z_hop": ["0.4"], "z_hop_types": ["Normal Lift"], - "change_filament_gcode": "PAUSE", - "machine_pause_gcode": "M0", + "change_filament_gcode": "M600", + "machine_pause_gcode": "PAUSE", "default_filament_profile": [ "Elegoo Generic PLA @0.2 nozzle" ], - "machine_start_gcode": "M413 S0 ; disable Power Loss Recovery\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S120 ; set temporary nozzle temp to prevent oozing during homing and auto bed leveling\nM140 S[bed_temperature_initial_layer_single] ; set final bed temp\nG4 S10 ; allow partial nozzle warmup\nG28 ; home all axis\nG1 Z50 F240\nG1 X2 Y10 F3000\n\nM190 S[bed_temperature_initial_layer_single] ; wait for bed temp to stabilize\nM109 S[nozzle_temperature_initial_layer] ; wait for nozzle temp to stabilize\nG1 Z0.28 F240\nG92 E0\nG1 Y140 E10 F1500 ; prime the nozzle\nG1 X2.3 F5000\nG92 E0\nG1 Y10 E10 F1200 ; prime the nozzle\nG92 E0", - "machine_end_gcode": "{if max_layer_z < printable_height}G1 Z{z_offset+min(max_layer_z+2, printable_height)} F600 ; Move print head up{endif}\nG1 X10 Y{print_bed_max[1]*0.8} F{travel_speed*60} ; present print\n{if max_layer_z < printable_height-10}G1 Z{z_offset+min(max_layer_z+10, printable_height-10)} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors", + "machine_start_gcode": ";ELEGOO NEPTUNE 4 MAX\nM220 S100 ;Set the feed speed to 100%\nM221 S100 ;Set the flow rate to 100%\nM104 S140\nM190 S[bed_temperature_initial_layer_single]\nG90\nG28 ;home\nG1 Z10 F300\nG1 X165 Y0.5 F6000\nG1 Z0 F300\nM109 S[nozzle_temperature_initial_layer]\nG92 E0 ;Reset Extruder\nG1 X165 Y0.5 Z0.4 F300 ;Move to start position\nG1 X265 E30 F400 ;Draw the first line\nG1 Z0.6 F120.0 ;Move to side a little\nG1 X260 F3000\nG92 E0 ;Reset Extruder", + "machine_end_gcode": ";PRINT_END\nG91 ;Relative positionning\nG1 E-2 F2700 ;Retract a bit\nG1 E-8 X5 Y5 Z3 F3000 ;Retract\nG90 ;Absolute positionning\nG1 X10 Y400 F6000;Finish print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z", "before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\nG92 E0\n;[layer_z]\n\n", "layer_change_gcode": ";AFTER_LAYER_CHANGE\n;[layer_z]", "scan_first_layer": "0" diff --git a/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Max (0.4 nozzle).json b/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Max (0.4 nozzle).json index cf91a968dcb..14186a34a8d 100644 --- a/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Max (0.4 nozzle).json +++ b/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Max (0.4 nozzle).json @@ -75,13 +75,13 @@ "wipe_distance": ["1"], "z_hop": ["0.4"], "z_hop_types": ["Normal Lift"], - "change_filament_gcode": "PAUSE", - "machine_pause_gcode": "M0", + "change_filament_gcode": "M600", + "machine_pause_gcode": "PAUSE", "default_filament_profile": [ "Elegoo Generic PLA @0.4 nozzle" ], - "machine_start_gcode": "M413 S0 ; disable Power Loss Recovery\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S120 ; set temporary nozzle temp to prevent oozing during homing and auto bed leveling\nM140 S[bed_temperature_initial_layer_single] ; set final bed temp\nG4 S10 ; allow partial nozzle warmup\nG28 ; home all axis\nG1 Z50 F240\nG1 X2 Y10 F3000\n\nM190 S[bed_temperature_initial_layer_single] ; wait for bed temp to stabilize\nM109 S[nozzle_temperature_initial_layer] ; wait for nozzle temp to stabilize\nG1 Z0.28 F240\nG92 E0\nG1 Y140 E10 F1500 ; prime the nozzle\nG1 X2.3 F5000\nG92 E0\nG1 Y10 E10 F1200 ; prime the nozzle\nG92 E0", - "machine_end_gcode": "{if max_layer_z < printable_height}G1 Z{z_offset+min(max_layer_z+2, printable_height)} F600 ; Move print head up{endif}\nG1 X10 Y{print_bed_max[1]*0.8} F{travel_speed*60} ; present print\n{if max_layer_z < printable_height-10}G1 Z{z_offset+min(max_layer_z+10, printable_height-10)} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors", + "machine_start_gcode": ";ELEGOO NEPTUNE 4 MAX\nM220 S100 ;Set the feed speed to 100%\nM221 S100 ;Set the flow rate to 100%\nM104 S140\nM190 S[bed_temperature_initial_layer_single]\nG90\nG28 ;home\nG1 Z10 F300\nG1 X165 Y0.5 F6000\nG1 Z0 F300\nM109 S[nozzle_temperature_initial_layer]\nG92 E0 ;Reset Extruder\nG1 X165 Y0.5 Z0.4 F300 ;Move to start position\nG1 X265 E30 F400 ;Draw the first line\nG1 Z0.6 F120.0 ;Move to side a little\nG1 X260 F3000\nG92 E0 ;Reset Extruder", + "machine_end_gcode": ";PRINT_END\nG91 ;Relative positionning\nG1 E-2 F2700 ;Retract a bit\nG1 E-8 X5 Y5 Z3 F3000 ;Retract\nG90 ;Absolute positionning\nG1 X10 Y400 F6000;Finish print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z", "before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\nG92 E0\n;[layer_z]\n\n", "layer_change_gcode": ";AFTER_LAYER_CHANGE\n;[layer_z]", "scan_first_layer": "0" diff --git a/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Max (0.6 nozzle).json b/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Max (0.6 nozzle).json index f8c08ef4146..622e1518bc2 100644 --- a/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Max (0.6 nozzle).json +++ b/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Max (0.6 nozzle).json @@ -75,13 +75,13 @@ "wipe_distance": ["1"], "z_hop": ["0.4"], "z_hop_types": ["Normal Lift"], - "change_filament_gcode": "PAUSE", - "machine_pause_gcode": "M0", + "change_filament_gcode": "M600", + "machine_pause_gcode": "PAUSE", "default_filament_profile": [ "Elegoo Generic PLA @0.6 nozzle" ], - "machine_start_gcode": "M413 S0 ; disable Power Loss Recovery\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S120 ; set temporary nozzle temp to prevent oozing during homing and auto bed leveling\nM140 S[bed_temperature_initial_layer_single] ; set final bed temp\nG4 S10 ; allow partial nozzle warmup\nG28 ; home all axis\nG1 Z50 F240\nG1 X2 Y10 F3000\n\nM190 S[bed_temperature_initial_layer_single] ; wait for bed temp to stabilize\nM109 S[nozzle_temperature_initial_layer] ; wait for nozzle temp to stabilize\nG1 Z0.28 F240\nG92 E0\nG1 Y140 E10 F1500 ; prime the nozzle\nG1 X2.3 F5000\nG92 E0\nG1 Y10 E10 F1200 ; prime the nozzle\nG92 E0", - "machine_end_gcode": "{if max_layer_z < printable_height}G1 Z{z_offset+min(max_layer_z+2, printable_height)} F600 ; Move print head up{endif}\nG1 X10 Y{print_bed_max[1]*0.8} F{travel_speed*60} ; present print\n{if max_layer_z < printable_height-10}G1 Z{z_offset+min(max_layer_z+10, printable_height-10)} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors", + "machine_start_gcode": ";ELEGOO NEPTUNE 4 MAX\nM220 S100 ;Set the feed speed to 100%\nM221 S100 ;Set the flow rate to 100%\nM104 S140\nM190 S[bed_temperature_initial_layer_single]\nG90\nG28 ;home\nG1 Z10 F300\nG1 X165 Y0.5 F6000\nG1 Z0 F300\nM109 S[nozzle_temperature_initial_layer]\nG92 E0 ;Reset Extruder\nG1 X165 Y0.5 Z0.4 F300 ;Move to start position\nG1 X265 E30 F400 ;Draw the first line\nG1 Z0.6 F120.0 ;Move to side a little\nG1 X260 F3000\nG92 E0 ;Reset Extruder", + "machine_end_gcode": ";PRINT_END\nG91 ;Relative positionning\nG1 E-2 F2700 ;Retract a bit\nG1 E-8 X5 Y5 Z3 F3000 ;Retract\nG90 ;Absolute positionning\nG1 X10 Y400 F6000;Finish print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z", "before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\nG92 E0\n;[layer_z]\n\n", "layer_change_gcode": ";AFTER_LAYER_CHANGE\n;[layer_z]", "scan_first_layer": "0" diff --git a/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Max (0.8 nozzle).json b/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Max (0.8 nozzle).json index 916695f13e1..9504347664a 100644 --- a/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Max (0.8 nozzle).json +++ b/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Max (0.8 nozzle).json @@ -75,13 +75,13 @@ "wipe_distance": ["1"], "z_hop": ["0.4"], "z_hop_types": ["Normal Lift"], - "change_filament_gcode": "PAUSE", - "machine_pause_gcode": "M0", + "change_filament_gcode": "M600", + "machine_pause_gcode": "PAUSE", "default_filament_profile": [ "Elegoo Generic PLA @0.8 nozzle" ], - "machine_start_gcode": "M413 S0 ; disable Power Loss Recovery\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S120 ; set temporary nozzle temp to prevent oozing during homing and auto bed leveling\nM140 S[bed_temperature_initial_layer_single] ; set final bed temp\nG4 S10 ; allow partial nozzle warmup\nG28 ; home all axis\nG1 Z50 F240\nG1 X2 Y10 F3000\n\nM190 S[bed_temperature_initial_layer_single] ; wait for bed temp to stabilize\nM109 S[nozzle_temperature_initial_layer] ; wait for nozzle temp to stabilize\nG1 Z0.28 F240\nG92 E0\nG1 Y140 E10 F1500 ; prime the nozzle\nG1 X2.3 F5000\nG92 E0\nG1 Y10 E10 F1200 ; prime the nozzle\nG92 E0", - "machine_end_gcode": "{if max_layer_z < printable_height}G1 Z{z_offset+min(max_layer_z+2, printable_height)} F600 ; Move print head up{endif}\nG1 X10 Y{print_bed_max[1]*0.8} F{travel_speed*60} ; present print\n{if max_layer_z < printable_height-10}G1 Z{z_offset+min(max_layer_z+10, printable_height-10)} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors", + "machine_start_gcode": ";ELEGOO NEPTUNE 4 MAX\nM220 S100 ;Set the feed speed to 100%\nM221 S100 ;Set the flow rate to 100%\nM104 S140\nM190 S[bed_temperature_initial_layer_single]\nG90\nG28 ;home\nG1 Z10 F300\nG1 X165 Y0.5 F6000\nG1 Z0 F300\nM109 S[nozzle_temperature_initial_layer]\nG92 E0 ;Reset Extruder\nG1 X165 Y0.5 Z0.4 F300 ;Move to start position\nG1 X265 E30 F400 ;Draw the first line\nG1 Z0.6 F120.0 ;Move to side a little\nG1 X260 F3000\nG92 E0 ;Reset Extruder", + "machine_end_gcode": ";PRINT_END\nG91 ;Relative positionning\nG1 E-2 F2700 ;Retract a bit\nG1 E-8 X5 Y5 Z3 F3000 ;Retract\nG90 ;Absolute positionning\nG1 X10 Y400 F6000;Finish print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z", "before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\nG92 E0\n;[layer_z]\n\n", "layer_change_gcode": ";AFTER_LAYER_CHANGE\n;[layer_z]", "scan_first_layer": "0" diff --git a/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Plus (0.2 nozzle).json b/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Plus (0.2 nozzle).json index 3895833b46d..913aaf9f49e 100644 --- a/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Plus (0.2 nozzle).json +++ b/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Plus (0.2 nozzle).json @@ -81,13 +81,13 @@ "wipe_distance": ["1"], "z_hop": ["0.4"], "z_hop_types": ["Normal Lift"], - "change_filament_gcode": "PAUSE", - "machine_pause_gcode": "M0", + "change_filament_gcode": "M600", + "machine_pause_gcode": "PAUSE", "default_filament_profile": [ "Elegoo Generic PLA @0.2 nozzle" ], - "machine_start_gcode": ";ELEGOO NEPTUNE 4 PLUS\nM220 S100 ;Set the feed speed to 100%\nM221 S100 ;Set the flow rate to 100%\nM104 S140\nM190 s[first_layer_bed_temperature]\nG90\nG28 ;home\nG1 Z10 F300\nG1 X115 Y0 F6000\nG1 Z0 F300\nM109 s[first_layer_temperature]\nG92 E0 ;Reset Extruder\nG1 X115 Y0 Z0.4 F300 ;Move to start position\nG1 X215.0 E30 F400 ;Draw the first line\nG1 Z0.6 F120.0 ;Move to side a little\nG1 X210 F3000\nG92 E0 ;Reset Extruder", - "machine_end_gcode": "G91 ;Relative positionning\nG1 E-2 F2700 ;Retract a bit\nG1 E-8 X5 Y5 Z3 F3000 ;Retract\nG90 ;Absolute positionning\nG1 X10 Y300 F6000;Finish print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z", + "machine_start_gcode": ";ELEGOO NEPTUNE 4 PLUS\nM220 S100 ;Set the feed speed to 100%\nM221 S100 ;Set the flow rate to 100%\nM104 S140\nM190 S[bed_temperature_initial_layer_single]\nG90\nG28 ;home\nG1 Z10 F300\nG1 X115 Y0.5 F6000\nG1 Z0 F300\nM109 S[nozzle_temperature_initial_layer]\nG92 E0 ;Reset Extruder\nG1 X115 Y0.5 Z0.4 F300 ;Move to start position\nG1 X215.0 E30 F400 ;Draw the first line\nG1 Z0.6 F120.0 ;Move to side a little\nG1 X210 F3000\nG92 E0 ;Reset Extruder", + "machine_end_gcode": ";PRINT_END\nG91 ;Relative positionning\nG1 E-2 F2700 ;Retract a bit\nG1 E-8 X5 Y5 Z3 F3000 ;Retract\nG90 ;Absolute positionning\nG1 X10 Y300 F6000;Finish print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z", "before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\nG92 E0\n;[layer_z]\n\n", "layer_change_gcode": ";AFTER_LAYER_CHANGE\n;[layer_z]", "scan_first_layer": "0" diff --git a/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Plus (0.4 nozzle).json b/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Plus (0.4 nozzle).json index ba889a48e08..9f84e7856d4 100644 --- a/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Plus (0.4 nozzle).json +++ b/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Plus (0.4 nozzle).json @@ -81,13 +81,13 @@ "wipe_distance": ["1"], "z_hop": ["0.4"], "z_hop_types": ["Normal Lift"], - "change_filament_gcode": "PAUSE", - "machine_pause_gcode": "M0", + "change_filament_gcode": "M600", + "machine_pause_gcode": "PAUSE", "default_filament_profile": [ "Elegoo Generic PLA @0.4 nozzle" ], - "machine_start_gcode": ";ELEGOO NEPTUNE 4 PLUS\nM220 S100 ;Set the feed speed to 100%\nM221 S100 ;Set the flow rate to 100%\nM104 S140\nM190 s[first_layer_bed_temperature]\nG90\nG28 ;home\nG1 Z10 F300\nG1 X115 Y0 F6000\nG1 Z0 F300\nM109 s[first_layer_temperature]\nG92 E0 ;Reset Extruder\nG1 X115 Y0 Z0.4 F300 ;Move to start position\nG1 X215.0 E30 F400 ;Draw the first line\nG1 Z0.6 F120.0 ;Move to side a little\nG1 X210 F3000\nG92 E0 ;Reset Extruder", - "machine_end_gcode": "G91 ;Relative positionning\nG1 E-2 F2700 ;Retract a bit\nG1 E-8 X5 Y5 Z3 F3000 ;Retract\nG90 ;Absolute positionning\nG1 X10 Y300 F6000;Finish print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z", + "machine_start_gcode": ";ELEGOO NEPTUNE 4 PLUS\nM220 S100 ;Set the feed speed to 100%\nM221 S100 ;Set the flow rate to 100%\nM104 S140\nM190 S[bed_temperature_initial_layer_single]\nG90\nG28 ;home\nG1 Z10 F300\nG1 X115 Y0.5 F6000\nG1 Z0 F300\nM109 S[nozzle_temperature_initial_layer]\nG92 E0 ;Reset Extruder\nG1 X115 Y0.5 Z0.4 F300 ;Move to start position\nG1 X215.0 E30 F400 ;Draw the first line\nG1 Z0.6 F120.0 ;Move to side a little\nG1 X210 F3000\nG92 E0 ;Reset Extruder", + "machine_end_gcode": ";PRINT_END\nG91 ;Relative positionning\nG1 E-2 F2700 ;Retract a bit\nG1 E-8 X5 Y5 Z3 F3000 ;Retract\nG90 ;Absolute positionning\nG1 X10 Y300 F6000;Finish print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z", "before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\nG92 E0\n;[layer_z]\n\n", "layer_change_gcode": ";AFTER_LAYER_CHANGE\n;[layer_z]", "scan_first_layer": "0" diff --git a/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Plus (0.6 nozzle).json b/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Plus (0.6 nozzle).json index 0ba5d6e2c07..2fad4a21c91 100644 --- a/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Plus (0.6 nozzle).json +++ b/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Plus (0.6 nozzle).json @@ -81,13 +81,13 @@ "wipe_distance": ["1"], "z_hop": ["0.4"], "z_hop_types": ["Normal Lift"], - "change_filament_gcode": "PAUSE", - "machine_pause_gcode": "M0", + "change_filament_gcode": "M600", + "machine_pause_gcode": "PAUSE", "default_filament_profile": [ "Elegoo Generic PLA @0.6 nozzle" ], - "machine_start_gcode": ";ELEGOO NEPTUNE 4 PLUS\nM220 S100 ;Set the feed speed to 100%\nM221 S100 ;Set the flow rate to 100%\nM104 S140\nM190 s[first_layer_bed_temperature]\nG90\nG28 ;home\nG1 Z10 F300\nG1 X115 Y0 F6000\nG1 Z0 F300\nM109 s[first_layer_temperature]\nG92 E0 ;Reset Extruder\nG1 X115 Y0 Z0.4 F300 ;Move to start position\nG1 X215.0 E30 F400 ;Draw the first line\nG1 Z0.6 F120.0 ;Move to side a little\nG1 X210 F3000\nG92 E0 ;Reset Extruder", - "machine_end_gcode": "G91 ;Relative positionning\nG1 E-2 F2700 ;Retract a bit\nG1 E-8 X5 Y5 Z3 F3000 ;Retract\nG90 ;Absolute positionning\nG1 X10 Y300 F6000;Finish print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z", + "machine_start_gcode": ";ELEGOO NEPTUNE 4 PLUS\nM220 S100 ;Set the feed speed to 100%\nM221 S100 ;Set the flow rate to 100%\nM104 S140\nM190 S[bed_temperature_initial_layer_single]\nG90\nG28 ;home\nG1 Z10 F300\nG1 X115 Y0.5 F6000\nG1 Z0 F300\nM109 S[nozzle_temperature_initial_layer]\nG92 E0 ;Reset Extruder\nG1 X115 Y0.5 Z0.4 F300 ;Move to start position\nG1 X215.0 E30 F400 ;Draw the first line\nG1 Z0.6 F120.0 ;Move to side a little\nG1 X210 F3000\nG92 E0 ;Reset Extruder", + "machine_end_gcode": ";PRINT_END\nG91 ;Relative positionning\nG1 E-2 F2700 ;Retract a bit\nG1 E-8 X5 Y5 Z3 F3000 ;Retract\nG90 ;Absolute positionning\nG1 X10 Y300 F6000;Finish print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z", "before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\nG92 E0\n;[layer_z]\n\n", "layer_change_gcode": ";AFTER_LAYER_CHANGE\n;[layer_z]", "scan_first_layer": "0" diff --git a/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Plus (0.8 nozzle).json b/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Plus (0.8 nozzle).json index 94c9c802a55..90774fe1c7d 100644 --- a/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Plus (0.8 nozzle).json +++ b/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Plus (0.8 nozzle).json @@ -81,13 +81,13 @@ "wipe_distance": ["1"], "z_hop": ["0.4"], "z_hop_types": ["Normal Lift"], - "change_filament_gcode": "PAUSE", - "machine_pause_gcode": "M0", + "change_filament_gcode": "M600", + "machine_pause_gcode": "PAUSE", "default_filament_profile": [ "Elegoo Generic PLA @0.8 nozzle" ], - "machine_start_gcode": ";ELEGOO NEPTUNE 4 PLUS\nM220 S100 ;Set the feed speed to 100%\nM221 S100 ;Set the flow rate to 100%\nM104 S140\nM190 s[first_layer_bed_temperature]\nG90\nG28 ;home\nG1 Z10 F300\nG1 X115 Y0 F6000\nG1 Z0 F300\nM109 s[first_layer_temperature]\nG92 E0 ;Reset Extruder\nG1 X115 Y0 Z0.4 F300 ;Move to start position\nG1 X215.0 E30 F400 ;Draw the first line\nG1 Z0.6 F120.0 ;Move to side a little\nG1 X210 F3000\nG92 E0 ;Reset Extruder", - "machine_end_gcode": "G91 ;Relative positionning\nG1 E-2 F2700 ;Retract a bit\nG1 E-8 X5 Y5 Z3 F3000 ;Retract\nG90 ;Absolute positionning\nG1 X10 Y300 F6000;Finish print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z", + "machine_start_gcode": ";ELEGOO NEPTUNE 4 PLUS\nM220 S100 ;Set the feed speed to 100%\nM221 S100 ;Set the flow rate to 100%\nM104 S140\nM190 S[bed_temperature_initial_layer_single]\nG90\nG28 ;home\nG1 Z10 F300\nG1 X115 Y0.5 F6000\nG1 Z0 F300\nM109 S[nozzle_temperature_initial_layer]\nG92 E0 ;Reset Extruder\nG1 X115 Y0.5 Z0.4 F300 ;Move to start position\nG1 X215.0 E30 F400 ;Draw the first line\nG1 Z0.6 F120.0 ;Move to side a little\nG1 X210 F3000\nG92 E0 ;Reset Extruder", + "machine_end_gcode": ";PRINT_END\nG91 ;Relative positionning\nG1 E-2 F2700 ;Retract a bit\nG1 E-8 X5 Y5 Z3 F3000 ;Retract\nG90 ;Absolute positionning\nG1 X10 Y300 F6000;Finish print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z", "before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\nG92 E0\n;[layer_z]\n\n", "layer_change_gcode": ";AFTER_LAYER_CHANGE\n;[layer_z]", "scan_first_layer": "0" diff --git a/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Pro (0.2 nozzle).json b/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Pro (0.2 nozzle).json index eeedf2d80b6..331408cc4e6 100644 --- a/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Pro (0.2 nozzle).json +++ b/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Pro (0.2 nozzle).json @@ -48,13 +48,13 @@ "45" ], "single_extruder_multi_material": "1", - "change_filament_gcode": "PAUSE", - "machine_pause_gcode": "M0", + "change_filament_gcode": "M600", + "machine_pause_gcode": "PAUSE", "default_filament_profile": [ "Elegoo Generic PLA @0.2 nozzle" ], - "machine_start_gcode": "M413 S0 ; disable Power Loss Recovery\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S120 ; set temporary nozzle temp to prevent oozing during homing and auto bed leveling\nM140 S[bed_temperature_initial_layer_single] ; set final bed temp\nG4 S10 ; allow partial nozzle warmup\nG28 ; home all axis\n;G29 ; run abl mesh\nM420 S1 ; load mesh\nG1 Z50 F240\nG1 X2 Y10 F3000\n\nM190 S[bed_temperature_initial_layer_single] ; wait for bed temp to stabilize\nM109 S[nozzle_temperature_initial_layer] ; wait for nozzle temp to stabilize\nG1 Z0.28 F240\nG92 E0\nG1 Y140 E10 F1500 ; prime the nozzle\nG1 X2.3 F5000\nG92 E0\nG1 Y10 E10 F1200 ; prime the nozzle\nG92 E0", - "machine_end_gcode": "{if max_layer_z < printable_height}G1 Z{z_offset+min(max_layer_z+2, printable_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.8} F{travel_speed*60} ; present print\n{if max_layer_z < printable_height-10}G1 Z{z_offset+min(max_layer_z+70, printable_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < printable_height*0.6}G1 Z{printable_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors", + "machine_start_gcode": ";ELEGOO NEPTUNE 4 PRO\nM220 S100 ;Set the feed speed to 100%\nM221 S100 ;Set the flow rate to 100%\nM104 S140\nM190 S[bed_temperature_initial_layer_single]\nG90\nG28 ;home\nG1 Z10 F300\nG1 X67.5 Y0 F6000\nG1 Z0 F300\nM109 S[nozzle_temperature_initial_layer]\nG92 E0 ;Reset Extruder\nG1 X67.5 Y0 Z0.4 F300 ;Move to start position\nG1 X167.5 E30 F400 ;Draw the first line\nG1 Z0.6 F120.0 ;Move to side a little\nG1 X162.5 F3000\nG92 E0 ;Reset Extruder", + "machine_end_gcode": ";PRINT END\nG91 ;Relative positionning\nG1 E-2 F2700 ;Retract a bit\nG1 E-8 X5 Y5 Z3 F3000 ;Retract\nG90 ;Absolute positionning\nG1 X10 Y220 F6000;Finish print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z", "before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\nG92 E0\n;[layer_z]\n\n", "layer_change_gcode": ";AFTER_LAYER_CHANGE\n;[layer_z]", "scan_first_layer": "0" diff --git a/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Pro (0.4 nozzle).json b/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Pro (0.4 nozzle).json index a8cd75a7b40..dac4f610321 100644 --- a/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Pro (0.4 nozzle).json +++ b/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Pro (0.4 nozzle).json @@ -48,13 +48,13 @@ "45" ], "single_extruder_multi_material": "1", - "change_filament_gcode": "PAUSE", - "machine_pause_gcode": "M0", + "change_filament_gcode": "M600", + "machine_pause_gcode": "PAUSE", "default_filament_profile": [ "Elegoo Generic PLA @0.4 nozzle" ], - "machine_start_gcode": "M413 S0 ; disable Power Loss Recovery\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S120 ; set temporary nozzle temp to prevent oozing during homing and auto bed leveling\nM140 S[bed_temperature_initial_layer_single] ; set final bed temp\nG4 S10 ; allow partial nozzle warmup\nG28 ; home all axis\n;G29 ; run abl mesh\nM420 S1 ; load mesh\nG1 Z50 F240\nG1 X2 Y10 F3000\n\nM190 S[bed_temperature_initial_layer_single] ; wait for bed temp to stabilize\nM109 S[nozzle_temperature_initial_layer] ; wait for nozzle temp to stabilize\nG1 Z0.28 F240\nG92 E0\nG1 Y140 E10 F1500 ; prime the nozzle\nG1 X2.3 F5000\nG92 E0\nG1 Y10 E10 F1200 ; prime the nozzle\nG92 E0", - "machine_end_gcode": "{if max_layer_z < printable_height}G1 Z{z_offset+min(max_layer_z+2, printable_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.8} F{travel_speed*60} ; present print\n{if max_layer_z < printable_height-10}G1 Z{z_offset+min(max_layer_z+70, printable_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < printable_height*0.6}G1 Z{printable_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors", + "machine_start_gcode": ";ELEGOO NEPTUNE 4 PRO\nM220 S100 ;Set the feed speed to 100%\nM221 S100 ;Set the flow rate to 100%\nM104 S140\nM190 S[bed_temperature_initial_layer_single]\nG90\nG28 ;home\nG1 Z10 F300\nG1 X67.5 Y0 F6000\nG1 Z0 F300\nM109 S[nozzle_temperature_initial_layer]\nG92 E0 ;Reset Extruder\nG1 X67.5 Y0 Z0.4 F300 ;Move to start position\nG1 X167.5 E30 F400 ;Draw the first line\nG1 Z0.6 F120.0 ;Move to side a little\nG1 X162.5 F3000\nG92 E0 ;Reset Extruder", + "machine_end_gcode": ";PRINT END\nG91 ;Relative positionning\nG1 E-2 F2700 ;Retract a bit\nG1 E-8 X5 Y5 Z3 F3000 ;Retract\nG90 ;Absolute positionning\nG1 X10 Y220 F6000;Finish print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z", "before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\nG92 E0\n;[layer_z]\n\n", "layer_change_gcode": ";AFTER_LAYER_CHANGE\n;[layer_z]", "scan_first_layer": "0" diff --git a/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Pro (0.6 nozzle).json b/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Pro (0.6 nozzle).json index 1309fa72b40..c60abcf5814 100644 --- a/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Pro (0.6 nozzle).json +++ b/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Pro (0.6 nozzle).json @@ -25,11 +25,11 @@ "retract_length_toolchange": ["2"], "deretraction_speed": ["45"], "single_extruder_multi_material": "1", - "change_filament_gcode": "PAUSE", - "machine_pause_gcode": "M0", + "change_filament_gcode": "M600", + "machine_pause_gcode": "PAUSE", "default_filament_profile": ["Elegoo Generic PLA @0.6 nozzle"], - "machine_start_gcode": "M413 S0 ; disable Power Loss Recovery\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S120 ; set temporary nozzle temp to prevent oozing during homing and auto bed leveling\nM140 S[bed_temperature_initial_layer_single] ; set final bed temp\nG4 S10 ; allow partial nozzle warmup\nG28 ; home all axis\n;G29 ; run abl mesh\nM420 S1 ; load mesh\nG1 Z50 F240\nG1 X2 Y10 F3000\n\nM190 S[bed_temperature_initial_layer_single] ; wait for bed temp to stabilize\nM109 S[nozzle_temperature_initial_layer] ; wait for nozzle temp to stabilize\nG1 Z0.28 F240\nG92 E0\nG1 Y140 E10 F1500 ; prime the nozzle\nG1 X2.3 F5000\nG92 E0\nG1 Y10 E10 F1200 ; prime the nozzle\nG92 E0", - "machine_end_gcode": "{if max_layer_z < printable_height}G1 Z{z_offset+min(max_layer_z+2, printable_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.8} F{travel_speed*60} ; present print\n{if max_layer_z < printable_height-10}G1 Z{z_offset+min(max_layer_z+70, printable_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < printable_height*0.6}G1 Z{printable_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors", + "machine_start_gcode": ";ELEGOO NEPTUNE 4 PRO\nM220 S100 ;Set the feed speed to 100%\nM221 S100 ;Set the flow rate to 100%\nM104 S140\nM190 S[bed_temperature_initial_layer_single]\nG90\nG28 ;home\nG1 Z10 F300\nG1 X67.5 Y0 F6000\nG1 Z0 F300\nM109 S[nozzle_temperature_initial_layer]\nG92 E0 ;Reset Extruder\nG1 X67.5 Y0 Z0.4 F300 ;Move to start position\nG1 X167.5 E30 F400 ;Draw the first line\nG1 Z0.6 F120.0 ;Move to side a little\nG1 X162.5 F3000\nG92 E0 ;Reset Extruder", + "machine_end_gcode": ";PRINT END\nG91 ;Relative positionning\nG1 E-2 F2700 ;Retract a bit\nG1 E-8 X5 Y5 Z3 F3000 ;Retract\nG90 ;Absolute positionning\nG1 X10 Y220 F6000;Finish print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z", "before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\nG92 E0\n;[layer_z]\n\n", "layer_change_gcode": ";AFTER_LAYER_CHANGE\n;[layer_z]", "scan_first_layer": "0" diff --git a/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Pro (0.8 nozzle).json b/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Pro (0.8 nozzle).json index 90ca1d242ec..9e4b916c796 100644 --- a/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Pro (0.8 nozzle).json +++ b/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Pro (0.8 nozzle).json @@ -39,11 +39,11 @@ "retract_length_toolchange": ["2"], "deretraction_speed": ["45"], "single_extruder_multi_material": "1", - "change_filament_gcode": "PAUSE", - "machine_pause_gcode": "M0", + "change_filament_gcode": "M600", + "machine_pause_gcode": "PAUSE", "default_filament_profile": ["Elegoo Generic PLA @0.8 nozzle"], - "machine_start_gcode": "M413 S0 ; disable Power Loss Recovery\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S120 ; set temporary nozzle temp to prevent oozing during homing and auto bed leveling\nM140 S[bed_temperature_initial_layer_single] ; set final bed temp\nG4 S10 ; allow partial nozzle warmup\nG28 ; home all axis\n;G29 ; run abl mesh\nM420 S1 ; load mesh\nG1 Z50 F240\nG1 X2 Y10 F3000\n\nM190 S[bed_temperature_initial_layer_single] ; wait for bed temp to stabilize\nM109 S[nozzle_temperature_initial_layer] ; wait for nozzle temp to stabilize\nG1 Z0.28 F240\nG92 E0\nG1 Y140 E10 F1500 ; prime the nozzle\nG1 X2.3 F5000\nG92 E0\nG1 Y10 E10 F1200 ; prime the nozzle\nG92 E0", - "machine_end_gcode": "{if max_layer_z < printable_height}G1 Z{z_offset+min(max_layer_z+2, printable_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.8} F{travel_speed*60} ; present print\n{if max_layer_z < printable_height-10}G1 Z{z_offset+min(max_layer_z+70, printable_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < printable_height*0.6}G1 Z{printable_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors", + "machine_start_gcode": ";ELEGOO NEPTUNE 4 PRO\nM220 S100 ;Set the feed speed to 100%\nM221 S100 ;Set the flow rate to 100%\nM104 S140\nM190 S[bed_temperature_initial_layer_single]\nG90\nG28 ;home\nG1 Z10 F300\nG1 X67.5 Y0 F6000\nG1 Z0 F300\nM109 S[nozzle_temperature_initial_layer]\nG92 E0 ;Reset Extruder\nG1 X67.5 Y0 Z0.4 F300 ;Move to start position\nG1 X167.5 E30 F400 ;Draw the first line\nG1 Z0.6 F120.0 ;Move to side a little\nG1 X162.5 F3000\nG92 E0 ;Reset Extruder", + "machine_end_gcode": ";PRINT END\nG91 ;Relative positionning\nG1 E-2 F2700 ;Retract a bit\nG1 E-8 X5 Y5 Z3 F3000 ;Retract\nG90 ;Absolute positionning\nG1 X10 Y220 F6000;Finish print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z", "before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\nG92 E0\n;[layer_z]\n\n", "layer_change_gcode": ";AFTER_LAYER_CHANGE\n;[layer_z]", "scan_first_layer": "0"